1 / 23

ECE 477 Design Review Team 2  Fall 2011

ECE 477 Design Review Team 2  Fall 2011. Members: Bo Yuan, Yimin Xiao, Yang Yang , Jintao Zhang. Outline. Project overview Project-specific success criteria Block diagram Component selection rationale Packaging design Schematic and theory of operation PCB layout

jiro
Download Presentation

ECE 477 Design Review Team 2  Fall 2011

An Image/Link below is provided (as is) to download presentation Download Policy: Content on the Website is provided to you AS IS for your information and personal use and may not be sold / licensed / shared on other websites without getting consent from its author. Content is provided to you AS IS for your information and personal use only. Download presentation by click this link. While downloading, if for some reason you are not able to download a presentation, the publisher may have deleted the file from their server. During download, if you can't get a presentation, the file might be deleted by the publisher.

E N D

Presentation Transcript


  1. ECE 477 Design Review Team 2  Fall 2011 Members: Bo Yuan, Yimin Xiao, Yang Yang, Jintao Zhang

  2. Outline • Project overview • Project-specific success criteria • Block diagram • Component selection rationale • Packaging design • Schematic and theory of operation • PCB layout • Software design/development status • Project completion timeline • Questions / discussion

  3. Project Overview • The project we propose is a digital oscilloscope with playback function that provides almost any function of a typical oscilloscope, such as digital sampling, signal processing, scaling, cursor setting, reconstruction and visualization of signals. Additional features such as recording and replicating signals as a function generator, and write data to external storage (SD card).

  4. Project-Specific Success Criteria • An ability to sample analog voltage signal range from -12 V to 12 V via BNC; • An ability to reconstruct and display the sampled signal on VGA display; • An ability to create user interface and realize basic signal measurements, such as frequency and peak-to-peak voltage; • An ability to store/load the sampled signal to/from external memory; • An ability to replay a stored signal.

  5. Block Diagram

  6. Block Diagram, System Level

  7. Component Selection Rationale • Power Supply: • Using a standard 20 pin-Computer power supply unit. (Easy to use) • Use linear transistor 7805/7905/78M33 to provide low noise signal. Although 5V and 3.3V are available from the power supply, but along with a ripple voltage at 300mV. No significant current will be drawn from +/-5V line, large ripple voltage will be used in driving the analog MUX (+/-12V) and FPGA module (+5V), which has its own on board linear power supply system. • Using a 3V voltage reference for A/D conversion reference.

  8. Component Selection Rationale • Analog circuit: • MAX14752: Analog MUX • Advantage: • Large tolerance (VSS-2 to VDD+2) compare to ADG1414 (VSS-0.3 to VDD+0.3). • Easy to control: Serial bus control, no SPI line require. • Got free sample from MAXIM, ADG1414 cost 8 dollar a piece. • Disadvantage: • High On-Resistance: 60 Ohm and ADG1414 is only 9.5 Ohm (Typ.). • More Pins to MCU: Each require four lines to controller, but ADG1414 is SPI shift register which can be implemented serially.

  9. Component Selection Rationale • INA118: Instrumentation Amplifier • Advantage: low distortion, high tolerance (+/-40V), voltage shift up by Vref(1.5V). • LF411: Output driver op-amp: • Advantage: Low offset, low distortion, high power (capable to drive coaxial wires)

  10. Component Selection Rationale • Digital Circuit: • MCU – STM32F407VG • Sampling rate 2.4 MHz maximum. • Relatively large RAM size (192 KB). • Crystal Clock: • 26MHz Crystal: Allowed maximum external clock. ARM Cortex-M4 will use an internal PLL to generate higher frequency clock up to 168MHz. Secondary clock (32.768KHz) is also laid out on board in case for need of precise clocking. • FPGA – Spartan 3E • VGA support. • Older version of the Spartan series, avoid voltage conversion.

  11. Packaging Design

  12. Schematic/Theory of OperationAnalog Input/ Output

  13. Schematic/Theory of OperationMicroprocessor

  14. Schematic/Theory of OperationDisplay Unit

  15. Schematic/Theory of OperationUser Interface

  16. PCB Layout: General Layout

  17. PCB Layout: Through Hole/Via

  18. PCB Layout: Top Copper

  19. PCB Layout: Bottom Copper

  20. Software Design/Development Status

  21. Software DesignDevelopment Status

  22. Project Completion Timeline

  23. Questions / Discussion

More Related