1 / 75

IDE and SCSI Devices

IDE and SCSI Devices. Terms and Definitions. Chapter Objectives. After completing this chapter you will: Understand hard drive terminology. Understand the different hard drive types. Be able to set up and configure different types of hard drives. Be able to troubleshoot hard drive problems.

jafari
Download Presentation

IDE and SCSI Devices

An Image/Link below is provided (as is) to download presentation Download Policy: Content on the Website is provided to you AS IS for your information and personal use and may not be sold / licensed / shared on other websites without getting consent from its author. Content is provided to you AS IS for your information and personal use only. Download presentation by click this link. While downloading, if for some reason you are not able to download a presentation, the publisher may have deleted the file from their server. During download, if you can't get a presentation, the file might be deleted by the publisher.

E N D

Presentation Transcript


  1. IDE and SCSI Devices Terms and Definitions

  2. Chapter Objectives After completing this chapter you will: • Understand hard drive terminology. • Understand the different hard drive types. • Be able to set up and configure different types of hard drives. • Be able to troubleshoot hard drive problems. • Understand and be able to perform hard drive preventive maintenance.

  3. Hard Drive Overview • Hard drives are the most popular devices for storing data. The hard drive subsystem can have up to three parts: • The hard drive • Cables that attach to an adapter or the motherboard • Control circuits located on an adapter or the motherboard

  4. Hard Drive Geometry • Components of a Hard Drive: • Platters are multiple hard metal surfaces contained in the hard drive. • Read/Write Heads write and read 1s and 0s to and from the hard drive surface. • A Head Crash occurs when a read/write head touches the hard drive platter. • Track is a concentric circle on a formatted floppy or hard drive platter. • Cylinder is one corresponding track on all surfaces of a hard drive. • Sectors – Each track is divided into sectors which contains 512 bytes of data. • ZBR (Zone Bit Recording) efficiently uses the hard drive surface by placing more sectors on the outer tracks than on the inner tracks. • Interleaving is a method of numbering sectors for the most efficient transfer of data between the hard drive and the controller. Today’s hard drives normally use a 1:1 interleave.

  5. Hard Drive Geometry Hard Drive Geometry IDE/SCSI – Figure #1

  6. Hard Drive Geometry Cylinder vs Tracks IDE/SCSI – Figure #2

  7. Hard Drive Geometry Sectors on Older Hard Drives IDE/SCSI – Figure #3

  8. Hard Drive Geometry Zone Bit Recording Sectors IDE/SCSI – Figure #4

  9. Hard Drive Geometry 3:1 Interleaving IDE/SCSI – Figure #5

  10. Hard Drive Interfaces Overview • There are four hard drive interfaces: • ST506 • ESDI • IDE (ATA) • SCSI • Encoding is the way 1s and 0s are placed on the drive.

  11. IDE (Integrated Drive Electronics) • IDE (Integrated Drive Electronics) is the most popular type of hard drive used in home and business computers. • DMA (Direct Memory Access) allows data transfer between the hard drive and RAM without going through the CPU. • PIO (Programmed Input/Output) is a speed standard for data transfers to and from the hard drive. • UDMA (Ultra DMA) allows the IDE interface to control the PCI bus for faster transfers. • SMART (Self-Monitoring Analysis & Report Technology) is part of the ATA-3 IDE standard for power management, drive analysis, and failure reporting. • CRC (Cyclic Redundancy Checking) is an advanced method of checking the data for errors. • ATAPI (AT Attachment Packet Interface) is the hardware side of the IDE specification that supports devices like CD and tape drives. • Serial ATA is a point to point interface in which each device connects to the host through a dedicated link and has the entire interface bandwidth.

  12. IDE (Integrated Drive Electronics) PIO Modes for IDE Hard Drives IDE/SCSI – Table #1

  13. IDE (Integrated Drive Electronics) DMA Modes for IDE Hard Drives IDE/SCSI – Table #2

  14. IDE (Integrated Drive Electronics) 80 and 40 Pin Conductor Cable IDE/SCSI – Figure #6

  15. IDE (Integrated Drive Electronics) IDE ATA Standards IDE/SCSI – Table #4

  16. SCSI (Small Computer System Interface) • SCSI (Small Computer System Interface) is an interface standard that connects multiple small devices to the same adapter via a SCSI bus. • SCSI bus is the bus shared by all devices that attach to one SCSI adapter. • Host Adapter connects the SCSI device to the motherboard and coordinates the activities of other devices connected.

  17. SCSI (Small Computer System Interface) SCSI Standards IDE/SCSI – Table #5

  18. Laptop Storage Devices • Laptops can use IDE or SCSI hard drives. • Laptop IDE hard drives are installed using two methods: • Proprietary installation is installed in a location that cannot be changed, configured, or moved very easily. • Removable IDE hard drives with a laptop are installed or removed through a 44-pin connector.

  19. SCSI Software Standards • Most SCSI hard drives have software built into the hard drive’s BIOS chip. Other drives must use one of three types of SCSI software standards: • ASPI (Advanced SCSI Programming Interface) • CAM (Common Access Method) • LADDR (Layered Device Driver Architecture)

  20. Drive Configuration Overview • The configuration of a hard drive usually includes setting jumpers on the drive, terminating properly, and performing a few software commands.

  21. IDE Device Configuration • IDE Hard Drives are normally configured using jumpers. • Single IDE setting is used when only one devices connects to the IDE cable. • Master IDE setting is a jumper setting used to configure an IDE device and is the controlling device on the interface. • Slave IDE setting is an IDE setting for the second device added to the IDE cable. The device should be a slower device than the master. • Cable Select is a setting used on IDE devices when a special cable determines which device is the master and which one is the slave. • DASP (Drive Active/Slave Present) is a signal in the ATA interface of the IDE connector that is used to indicate the presence of a slave IDE device. • Master/Slave configuration can be found on 9-19.

  22. IDE Device Configuration IDE Motherboard Connectors IDE/SCSI – Figure #7

  23. IDE Device Configuration IDE Hard Drive Set as Master IDE/SCSI – Figure #8

  24. IDE Device Configuration Two IDE Hard Drives IDE/SCSI – Figure #9

  25. Serial ATA (SATA) Installation • Serial ATA drives are easy to install. • Serial ATA drives do not have any master/slave, cable select, or termination settings • Uses a small 7-pin connector that attaches between the serial ATA controller and the serial ATA drive • Installation instructions for serial ATA drives can be found on 9-25.

  26. Serial ATA (SATA) Installation Installed SATA Hard Drive and Adapter IDE/SCSI – Figure #12

  27. SCSI Configuration • A SCSI device is configured by: • Setting the proper SCSI ID • Terminating both ends of the SCSI chain • Connecting the proper cables • A SCSI ID is the priority number assigned to each device connected by a SCSI chain.

  28. SCSI ID Configuration • Standard SCSI devices recognize SCSI IDs 0 through 7. • Wide SCSI devices recognize SCSI IDs 0 through 15. • Power on all external SCSI devices before powering on the computer. • Each SCSI device must have a unique SCSI ID. • SCAM (SCSI Configured AutoMatically) allows for automatic SCSI ID assignment.

  29. SCSI ID Configuration SCSI ID Settings (Most Significant Bit to the Left) IDE/SCSI – Table #7

  30. SCSI ID Configuration Two Internal SCSI Devices – SCSI IDs IDE/SCSI – Figure #13

  31. SCSI ID Configuration Two External SCSI Devices – SCSI IDs IDE/SCSI – Figure #14

  32. SCSI Termination • SCSI termination is performed in several different ways: • By installing a SIPP • By installing a jumper • By setting a switch • By installing a terminator plug • By installing a pass-through terminator • Through software

  33. SCSI Termination • The SCSI bus cannot operate properly without terminating both ends of the SCSI bus. • SE (Single Ended) is a type of SCSI electrical signal and terminator used with most SCSI devices. • Passive Terminators are one type of SCSI chain end that is susceptible to noise interference over long cable distances. It is used with SCSI-1 devices. • Active Terminators are a type of end to a SCSI chain that allows for longer cable distance and provides correct voltage for SCSI signals. • FPT (Forced Perfect Termination) is a special type of active terminator that can be used with SE devices. • HVD (High Voltage Differential) is a SCSI-2 standard that allowed longer SCSI bus lengths and required a differential terminator. HVD was removed from the SCSI-3 standards. • Differential Terminator is a SCSI terminator used with HVD SCSI devices. It cannot be used with other SCSI types. • LVD (Low Voltage Differential) is a SCSI signaling type that is required on all SCSI devices that adhere to the Ultra SCSI standards. LVD is backwards compatible with SE. • Pass Through Terminator allows a device that does not have terminators to be terminated through the connector that attaches to the cable.

  34. SCSI Termination SCSI Termination IDE/SCSI – Figure #15

  35. SCSI Termination Today’s SCSI Terminators: Pass Through Terminator and 68-Pin Active Terminator IDE/SCSI – Figure #17

  36. SCSI Termination SCSI Symbols IDE/SCSI – Figure #19

  37. SCSI Termination Two Internal SCSI Devices - Termination IDE/SCSI – Figure #20

  38. SCSI Termination Two External SCSI Devices - Termination IDE/SCSI – Figure #21

  39. SCSI Termination Internal and External SCSI Devices - Termination IDE/SCSI – Figure #22

  40. SCSI Cables • SCSI cabling allows multiple devices to be connected to one SCSI host adapter and share the same SCSI bus. • Most internal SCSI-1 and SCSI-2 cables are 50-pin ribbon cables. They are also known as an A cable. • Internal SCSI-3 cables are 68-pin ribbon cables. • When installing multiple SCSI devices, install one device at a time. • Always avoid using the cheaper, thinner SCSI cables. They are more susceptible to outside noise.

  41. SCSI Cables Internal SCSI Cables IDE/SCSI – Figure #23

  42. SCSI Cables External SCSI Cables IDE/SCSI – Figure #24

  43. SCSI Cables SCSI Cables and Connectors IDE/SCSI – Table #9

  44. System Configuration for Hard Drives • Hard drives are configured through the Setup program with a drive type number. • Drive Type is a number that corresponds to a drive’s geometry (the number of cylinders, heads, and sectors). • IDE hard drives are normally configured using the Auto-Detect feature included with BIOS. This feature automatically determines the drive type for the system.

  45. BIOS Configurations for Hard Drives • Most system BIOS chips manufactured before 1994 use INT13 to recognize hard drives up to 504MB. • INT13 Interface or Interrupt 13 is a standard that allows a system BIOS to locate data on the hard drive. • LBA (Logical Block Addressing) allows hard drives to be recognized up to 8GB in capacity. • Extended INT13 Interface can support drives larger than 8GB in capacity.

  46. Hard Drive Preparation Overview • Three steps to hard drive preparation: • Low-Level Format • Partition • High-Level Format

  47. Partitioning • Partitioning divides a hard drive so that the computer system sees more than one drive. • FDISK is a command used to partition a hard drive. • A File System defines how data is stored on a drive. • FAT (File Allocation Table) is a method of organizing a computer’s file system. • FAT16 file system is supported by DOS, Windows 9x, NT, 2000, and XP. • FAT32 file system used by Windows 95 Service Release 2, Windows 98, Windows 2000, and XP that supports hard drives up to 2TB in size. • NTFS (NT File System) file system used with Windows NT, 2000, and XP.

  48. Partitioning • Types of Partitions: • The Primary Partition is the first detected drive on the hard drive. • The Extended Partition is a hard drive division • Logical Drives divides the extended partition into separate units which appear as separate drive letters. • System Partition is a type of active hard drive partition found in Windows NT and 2000 that contains the hardware-specific files needed to load the operating system. • Boot Partition – A type of partition found in Windows NT and 2000 that contains the operating system. • The Partition Table holds the information about the types and locations of partitions created. It is part of the master boot record. • MBR (Master Boot Record) is a program that reads the partition table to find the primary partitions used to boot the system.

  49. Partitioning Clusters IDE/SCSI – Figure #25

  50. Partitioning FAT16 Partitions and Cluster Size IDE/SCSI – Table #12

More Related