1 / 31

Wood and Plastics

Wood and Plastics. Major Topics. Classification of Wood Hardwood Softwood Growth of Wood Wood Defects Wood (Lumber) Seasoning/Kiln Drying Moisture Content Cutting. Major Topics con’t. Wood (Lumber) Decay/Insects Grading Sizing (Nominal vs. Actual) Joints Fasteners

Download Presentation

Wood and Plastics

An Image/Link below is provided (as is) to download presentation Download Policy: Content on the Website is provided to you AS IS for your information and personal use and may not be sold / licensed / shared on other websites without getting consent from its author. Content is provided to you AS IS for your information and personal use only. Download presentation by click this link. While downloading, if for some reason you are not able to download a presentation, the publisher may have deleted the file from their server. During download, if you can't get a presentation, the file might be deleted by the publisher.

E N D

Presentation Transcript


  1. Wood and Plastics

  2. Major Topics • Classification of Wood • Hardwood • Softwood • Growth of Wood • Wood Defects • Wood (Lumber) • Seasoning/Kiln Drying • Moisture Content • Cutting

  3. Major Topics con’t • Wood (Lumber) • Decay/Insects • Grading • Sizing (Nominal vs. Actual) • Joints • Fasteners • Prefabricated Wood (Glue-laminated)

  4. Major Topics con’t • Plywood • Other Panels • Waferboard • Composite • Particleboard • OSB (Oriented Strand Board) • Plastics

  5. Classification of Wood • Hardwood – trees which are deciduous (shed broad shaped leaves annually) ex: Birch, Ash, Maple, Oak • Softwood – trees which are evergreen (needle-like leaves) ex: Southern Pine, Fir, Spruce, Redwood

  6. Growth of Wood • Growth is formed from core (pith) in rings. The # of rings and spacing between rings show age and growing conditions of tree. • Wood is made of hollow tubular cells running parallel to the long axis of the tree.

  7. Wood Defects • Common defects include: knots, stain, pitch pockets, decay, and cracks. • These defects will impact the visual “grading” of wood products

  8. Examples of Defects Wane – irregular rounding caused by cutting too close to outside of log Knot Resin Pocket

  9. Lumber • Broad term that applies to all finished or semi-finished wood shaped with parallel longitudinal surfaces • Nominal piece sizing includes: • Board -- 11/2” or less thick and 2” or more wide • Dimension – 2” to 5” thick and >2” wide • Timbers -- 5” or more thick and wide

  10. Lumber Measured in “Board Feet” http://www.woodzone.com/tips/board_feet/board_feet.htm

  11. Seasoning/Kiln Drying • Seasoning- the process of reducing moisture until a suitable level is achieved (causes shrinking in lumber size) • May be seasoned in the air (2-6 months for softwood and may take 4 years for some hardwoods) or by using a kiln • A chemical (hygroscopic) may be applied to the wood to keep surface moist to reduce shrinkage cracks (checks)

  12. Moisture Content • The strength of wood increases as the moisture content (m.c.) decreases • M.C. varies depending on the conditions (geographical region & indoor/outdoor) in which the lumber will be used • Typically, m.c. does not exceed 19%

  13. Cutting • Plain-sawed (flat sawed) – lumber which is cut in parallel slides [less waste & cheaper; warps & splits] • Edge-sawed – lumber which is cut perpendicular to the exterior of the tree • Quarter-sawed – lumber in which the log is 1st cut into quarters and then cut on the diagonal [produces the most attractive wood grains]

  14. Decay-Insects • Termites – destroy wood by chewing it (chemical or physical barriers should be used to deter them) • Fungi – feed on wood fibers leaving wood weakened with rotting • Avoid placing untreated wood directly in contact with concrete

  15. Pressure-Treated Lumber • Must meet all EPA (Environmental Protection Agency) requirements • CCA (Chromated Copper Arsenate) is the most common treatment used today • 4- EPA approved wood preservatives include • Waterborne • Oil-borne • Creosote • Fire-retardant solutions

  16. Grading • Depends on the appearance ( # of defects) and strength • Lumber pieces are marked with a grade stamp • Typical stamp includes • Grading body (WWP – Western Wood Products • Mill identification • Grade name (Const – construction) • Moisture content • Type of wood (D-Fir – Douglas Fir)

  17. Sizing (Nominal vs. Actual) • Lumber is referred to by nominal size but the actual size is less (see handout) • 2”x4” actually measures 1/1/2” x 3 ½” • 1” x 8” actually measures ¾” x 71/4”

  18. Joints

  19. Fasteners • Nails, screws, bolts, staples, anchors, and joist hangers are common fasteners • Sizes, styles, and finishes (coatings) depend on the intended application • Length of nails designated in “pennies” [d]

  20. Nails

  21. Prefabricated Wood • Because of the limitations of size of sawn wood – the gluing of smaller pieces together will enable structural members of virtually any length, cross-section, and desired curves to be made • Glu-lam members are widely used in areas of construction using arches (must comply with ANSI 190.1)

  22. Glu-Lam • Individual laminations are placed so that: • Weak spots are separated from each other to avoid concentration of weakness • Appearance flaws in wood are hidden within the member • End joints between lams are separated from each other to avoid a plane of weakness • The strongest wood is placed where stresses are highest

  23. Species of Lumber Used for Glu-Lam • Douglas Fir • Alaska Cedar • Spruce-Pine Fir • Southern Pine

  24. Plywood • Plywood is a type of glued, laminated wood. Thin wood layers of laminations are arranged with the grains of each layer perpendicular to the adjacent one. • Veneers – the actual laminations consisting of face & back, crossbands, and the inner (core) [see fig 6-20, pg. 176] • Usually an odd number of veneers (3-5; may be up to 11) • Thickness may range from ¼” – 1 ¼”

  25. Advantages of Plywood vs. Sawn Lumber • Has great transverse strength which aids in strengthening/bracing entire structure when used over studs, joists, and rafters for wood frame construction • Less warping and change due to moisture changes • Is more easily bent to form curves for concrete forms or curved wood construction • Fabricated in large sheets (4’x8’, typical) which covers larger areas more quickly • Can be worked closer to the edges without splitting • Desired appearance can be obtained by using thin veneers of high quality wood where they are visible

  26. Grades/Types of Plywood • 5 basic grades from best to less desirable finished appearance: A, B, C, C plugged, & D • 5 species groups (according to stiffness and strength): Group 1 is the strongest/stiffest • Types of plywood: interior and exterior • Interior- made with glue suitable for indoor use; available in any grade • Exterior – made with hot, phenolic resin glue which is unaffected by water & resists weathering; no veneers below C grade used

  27. APA – Engineered Wood Products • APA – American Plywood Association – key organization for plywood information • Website link: http://www.apawood.org/

  28. Other Panels • Waferboard • Composite • Particleboard • OSB (Oriented Strand Board)

  29. Plastics • Usually contain synthetic resins. May also contain plasticizers, fillers, and colorants • 2 basic classes of plastics; thermoplastics (no chemical change during heating/cooling) & thermosetting plastics (change chemically when heated and solidify while still hot) • Plastic products are strong, light in weight, formable, and resistant to corrosion

  30. Thermoplastics

  31. Thermosetting

More Related