1 / 35

Ridgeline Meteorological Sensor Network

Ridgeline Meteorological Sensor Network. Stephen Copeland, Xau Moua, Joseph Lane, Robert Akerson Client: Doug Taylor, John Deere Renewables Advisors: Dr. Manimaran Govindarasu, Dr.Venkataramana Ajjarapu. Project Plan.

ivo
Download Presentation

Ridgeline Meteorological Sensor Network

An Image/Link below is provided (as is) to download presentation Download Policy: Content on the Website is provided to you AS IS for your information and personal use and may not be sold / licensed / shared on other websites without getting consent from its author. Content is provided to you AS IS for your information and personal use only. Download presentation by click this link. While downloading, if for some reason you are not able to download a presentation, the publisher may have deleted the file from their server. During download, if you can't get a presentation, the file might be deleted by the publisher.

E N D

Presentation Transcript


  1. Ridgeline Meteorological Sensor Network Stephen Copeland, Xau Moua, Joseph Lane, Robert Akerson Client: Doug Taylor, John Deere Renewables Advisors: Dr. Manimaran Govindarasu, Dr.Venkataramana Ajjarapu

  2. Project Plan • Small scout towers capable of wirelessly transmitting measurements to large MET towers. • Wireless communication via radio transceivers on scout tower and MET tower. • Built-in mesh networking protocol

  3. Design Scope Signal Converter

  4. Microcontroller and Wireless Shield Microcontroller Arduino Runs programmed code to send and receive data on mesh network Wireless Shield Xbee Provides easy form of adapter from transceiver to arduino due to header misalignment.

  5. Transceiver and Antenna Transceiver Xbee-PRO digimesh 900 Provides mesh protocol Transmits data to other node Antenna 7" ½ wave dipole, bulkhead mount, RPSMA connector Omni-directional transmission of data

  6. Wind Sensors Wind Vane NRG#200P Provides wind direction Angle from North=(360’/Vin)*Vout Vout ranging from 0 to Vin Anemometer NRG#40C Provides wind speed Generates a sine wave whose frequency determines wind speed

  7. Sensor Circuitry Used to transform the Sine wave output from the Anemometer into a square wave which provides the arduino with a frequency that represents the measured wind speed.

  8. Sensor Circuitry Cont.

  9. Arduino Code Anemometer Output Signal • Scout Tower Code • Reads the Voltage Signal at selected pins of the Arduino • Aggregates data at a user specified interval Measures Pulse Width Converts Pulse Width to Wind Speed Sends Wind Speed to Serial Port

  10. Arduino Code cont. • Central transceiver code • Receives data from all other nodes in the mesh network • Aggregates all of the data • Prints new data set to a text file Reads Signal From Transceivers Sends Data To Computer Averages Wind Speed Data

  11. Testing • Sensor Testing • PCB Functionality Testing • Range Evaluations • Elevated testing locations north of Ames • Power consumption • Use of multi meters to measure current and voltage levels • Microcontroller • Basic data communication

  12. Further Testing • Self Healing • Selected modules turned off during transmission • Security • Encryption of data being transmitted • Latency • Receiving rate vs. data size • Casing • Shock, vibration, realistic impact, and contact with water, ice, and snow.

  13. Sensor Testing Anemometer Results • We connected the anemometer directly to an oscilloscope • Signal amplitude and frequency increases as wind speed increases

  14. Sensor Testing Wind Vane Results • We connected the wind vane to 5V power supply • Oscilloscope gives output voltage over time • Voltage varies as wind vane changes direction from 0 to 360 degrees

  15. PCB Functionality Testing and Anemometer Results • Able to obtain a sine wave from the anemometer • Outputs a square wave with a frequency relative to the actual wind speed

  16. Aggregated Data Simulation • Wind speed in mph • Top node 1 • Middle node 2 • Both sampled and averaged every 10 seconds • Bottom average of node 1 and 2 calculated every 10 seconds

  17. Microcontroller Results • Successful interfacing to the sensors and PCB for gathering of data • Aggregation of data from sensors • Storage of data as MPH in a text file from output

  18. Antenna Results • Found optimal frequency of our antennas to be marker 1 • Freq= 896.247MHz marker 1 freq=896.2473 MHz dB(S(1,1))=13.97 marker 2 freq=1.8014 GHz dB(S(1,1))=13.66

  19. Results for Rough Terrain Testing • We attached sensors to the roof of CooverHall. • Successful transmission of data to motors lab from two nodes on roof • Simulated rugged terrain at Veenker golf course north of campus • Achieved an approximate range of 0.8 Km between nodes.

  20. Results for Range Testing • Tested North of Ames on a flat gravel road • Achieved an approximate range of 1.75Km

  21. Power Consumption Results • We spliced the USB cable between the device and PC • Connected inner USB wiring to a multi meter • Through the use of P=I*V we determined the required power to be around 0.5 Watts

  22. Self Healing Results Node 1 • Placement of four nodes at a certain distance preventing direct communication between first and last node • Upon the removal of a middle node from the system the line of communication is not broken Node 2 Node 3 Receiving Node User

  23. Security and Latency Results • 128-bit encryption is incorporated in the protocol for the transceivers • Client required only verification of encryption setting in transceivers

  24. Security and Latency Results • Node 1 sends current time to node 2 • Node 2 computes difference from it’s current time Time Synchronized Time Synchronized Node 2 Node 1

  25. Security and Latency Results

  26. Case Testing Results • Remained water tight under running water • Absorbed force from hammer without damage to the inner components • Withstood 6℉ without damage

  27. Mounting System • Consists of sections of PVC and Brass connectors to ensure stability for the sensors • Nema-4 enclosure • Clamped to vent pipes on the roof of Coover Hall

  28. Cost of Product

  29. Task Breakdown

  30. Fall Semester Project Schedule

  31. EE 491 Wind Turbine Project • Utilizes aggregated wind speed from the roof of Coover • USB interface with transceiver and Desktop PC • Uses Labview Software to run motor • Motor is coupled to a wind turbine which simulates wind power generation.

  32. EE491 Wind Turbine Project cont. http://seniord.ece.iastate.edu/may1101

  33. Recommendations • Use of renewable energy power source (wind or solar) • Integration of CFD into calculations for Wind Turbine project • Addition of more sensors to device • GPS units • Temperature Sensors • Barometers This would allow for better analysis of potential wind generation locations

  34. Acknowledgements • Leland Harker, ISU Parts Shop • Senior Design Team SD MAY11-01 • Doug Taylor, John Deere • Brad Luhrs & Bryan Burkhardt , DMACC • Dr. Manimaran Govindarasu • Dr. Venkataramana Ajjarapu

  35. Thank You Any Questions?

More Related