1 / 28

Powerline Communications: Channel Characterization and Modem Design

Powerline Communications: Channel Characterization and Modem Design. Yangpo Gao Helsinki University of Technology yangpo.gao@nokia.com 2005-10-18. Thesis Contents. Table of Contents Introduction PLC Technology Background Channel Measurement and Modeling Disturbance over PLC

gwenllian
Download Presentation

Powerline Communications: Channel Characterization and Modem Design

An Image/Link below is provided (as is) to download presentation Download Policy: Content on the Website is provided to you AS IS for your information and personal use and may not be sold / licensed / shared on other websites without getting consent from its author. Content is provided to you AS IS for your information and personal use only. Download presentation by click this link. While downloading, if for some reason you are not able to download a presentation, the publisher may have deleted the file from their server. During download, if you can't get a presentation, the file might be deleted by the publisher.

E N D

Presentation Transcript


  1. Powerline Communications:Channel Characterization and Modem Design Yangpo Gao Helsinki University of Technology yangpo.gao@nokia.com 2005-10-18

  2. Thesis Contents • Table of Contents • Introduction • PLC Technology Background • Channel Measurement and Modeling • Disturbance over PLC • DMT Based PLC Modem Design • Conclusion • Reference • This thesis is part of project “ PLC controlled LEDs for general lighting system”, which is sponsored by TEKES

  3. Introduction

  4. History of PLC and Motivation of Thesis • What is PLC • PLC – Powerline Communications • Using powerline as transmission medium for data communication • History of PLC • From high voltage (HV) low voltage (LV) • Low data rate high data rate • Control application multimedia data applications • Motivation • Cheap “the last mile” solution • However, worse channel than other wired network • Channel characterization reliable communications

  5. PLC Technology Background

  6. PLC Technologies • Three network levels • High voltage (110–380 kV) • Medium voltage (10–30 kV) • Low voltage (230/400 V, in the USA 110 V) (my thesis range) • Efficient coupling • Inductive coupling • Conductive coupling • Modulation and error correction • OFDM, DMT • CDMA • FEC

  7. EMC Issues • EMC --Electromagnetic compatibility • The ability of a device or system to function satisfactorily in its electromagnetic environment without introducing intolerable electromagnetic disturbances in the form of interferences to any other system in that environment, even to itself.

  8. International National Regional Standardizations • PLC standardization bodies

  9. Channel Measurement and Modeling

  10. Attenuation constant Propagation constant phase constant Characteristic impedance Transmission Line Theory • A piece of mains cable can be modeled as following figure R : resistance . L : inductance. G : conductance C : capacitance

  11. Channel Measurement Setup • Equipment: • Network Analyzer (NA) • Coupling Circuit • Coupling circuit • Conductive coupling • High pass filter • Galvanic isolation • Over Voltage protection

  12. Cable transversal • Rapid fluctuation caused by impedance mismatch • Maximum of 4 dB attenuation difference @ 100 MHz PLC Cable Measurements

  13. PLC Channel Measurements • Scenario 1: Internet access and distribution • Scenario 2: Home networking Scenario 1: Network topology is known, or easy to estimate. Channel is simple, and has few multipath components Scenario 2: Network topology is unknown or it is hard to define. Channel acts as black box. A lot of multipath components

  14. Frequency Domain Time Domain Channel Responses Scenario 1 Scenario 2

  15. PLC Channel Modeling • According to PLC channel multipath phenomenon, channel can be modeled as:

  16. Disturbance over PLC

  17. PLC Noise • Noise Classification: • Colored background noise • Narrowband noise • Periodic impulsive noise, asynchronous to the main frequency • Periodic impulsive noise, noise, synchronous to the main frequency • Asynchronous impulsive noise • Our concentration • Colored background noise • Asynchronous impulsive noise

  18. Noise Measurement setup • Equipment: • Oscilloscope • Spectrum Analyzer • Coupler

  19. Colored Background Noise • Quasi-Static behavior • Statistic information is extracted in table • Can be modeled as:

  20. Random Impulsive Noise • Caused by frequency bursts generated by electrical devices connected to the powerline. • Statistic information is extracted

  21. NEXT Formation FEXT Formation Other Disturbance • NEXT (Near End crosstalk) • FEXT (Far End crosstalk).

  22. DMT Based PLC Modem Design

  23. DMT Technology • Discrete Multi-tone Modulation (DMT) • Advantages: • Multicarrier technology – combat frequency selective fading • Dynamic bit loading based on SNR – efficient spectrum utilization • High channel capacity

  24. DMT Based PLC Modem Design • Simulation environment: • MATLAB SimuLink • MATLAB DSP Blockset Simulated channel response • Expected result • Bit Error Rate (BER)

  25. Modem performance PLC vs AWGN Simulation and Performance Optimized bit loading algorithm Signal spectrum before PLC channel Signal spectrum after PLC channel

  26. Publications Related to My Thesis

  27. Publications • More information can be found in my publications: • “Channel modeling and modem design for broadband power line communications”, Proceeding of ISPLC 2004, April, Spain • “Broadband characterization of indoor powerline channel”, Proceeding of ISPLC 2004, April, Spain • “Broadband Characterization of Indoor Powerline Channel and Its Capacity Consideration”, Proceeding of ICC 2005, May, Korea

  28. Any Questions? Thank You!

More Related