1 / 16

FRACTURE MECHANICS

FRACTURE MECHANICS. CRACK ?? FRACTURE ??? MECHANICS OF MATERIAL/STRENGTH OF MATERIAL ??. ASSUMPTION. HOMOGEN CONTINUE ISOTROPI. CASES. 1800 – 1870 : Accidents were caused by Fractures of wheel, axle, rails (Great Britain). 19 th March 1830 : Montrose Suspension Bridge.

gulleya
Download Presentation

FRACTURE MECHANICS

An Image/Link below is provided (as is) to download presentation Download Policy: Content on the Website is provided to you AS IS for your information and personal use and may not be sold / licensed / shared on other websites without getting consent from its author. Content is provided to you AS IS for your information and personal use only. Download presentation by click this link. While downloading, if for some reason you are not able to download a presentation, the publisher may have deleted the file from their server. During download, if you can't get a presentation, the file might be deleted by the publisher.

E N D

Presentation Transcript


  1. FRACTURE MECHANICS • CRACK ?? • FRACTURE ??? • MECHANICS OF MATERIAL/STRENGTH OF MATERIAL ??

  2. ASSUMPTION • HOMOGEN • CONTINUE • ISOTROPI

  3. CASES • 1800 – 1870 : Accidents were caused by Fractures of wheel, axle, rails (Great Britain). • 19th March 1830 : Montrose Suspension Bridge. Main chain gave way  700 persons killed. • 22nd January 1866 : A portion of roof of the Manchester railway station fell. 2 men death. Caused by failure of cast iron struts connected. • 13th December 1898 : The failure of a large gas tank in New York. • 3th January 1913 : A high pressure water burst at Boston  flooded the district • February 1866 : Boiler explosions • Most of serious railway accidents • Spec pipa : API. 5 LX grade X52, electric • resistance welded, longitudinal weld pipa - Mechanical properties : σu, σy - Dimensi pipa : Ø 16” , t = 0,250” • Kondisi operasi : p = 600 psig (avg) • Sistem perlindungan • - Kondisi lingkungan POOR DESIGN

  4. Fracture mechanics • LINEAR ELASTIC FRACTURE MECHANICS (LEFM) * BEBAN ELASTIS == FATIGUE • ELASTIC PLASTIC FRACTURE MECHANICS * BEBAN PLASTIS

  5. STRESS CONCENTRATION FACTOR (Kt) • RADIUS OF FILLET • r/D • r/D<<< = Kt >>> • Notch stress (σnotch)>>> • σnotch = Kt x σunnotch/ σn Bagaimana kalau r ~ 0, D = constant r/D = 0/D ~ infinite = crack/retak Crack # notch/hole Kt = faktor pengendali konstruksi yang ada notch

  6. SOURCES OF STRESS CONCENTRATED • IMPURITY,VACANCY,DISLOCATION,GRAIN BOUNDARY • ROUGHNESS OF SURFACE • WELD DEFECT • HOLE FOR RIVET, BOLT “DON’T CONSIDER TO AVOID FRACTURE”, BUT CONSIDER “TO CONTROL FRACTURE” IN DESIGN, MANUFACTURING, MAINTENANCE AND REPAIR.

  7. What is CRACK???? • Notch yang r ~ 0 • Alat kontrolnya bukan lagi Kt • K1 , K2 atau K3 (factor intensitas tegangan/ stress intensity factor) • KI = MODUS I , tension • KII = modus II, sliding • KIII = modus III, tearing

  8. Crack size Residual strength Design strength Expected highest service load Expected highest service load Normal sevice load Failure may occure failure Cycles/time Crack size, time

  9. FRACTURE/PATAH • AWAL RETAK/CRACK INITIATION • CRACK PROPAGATION • FINAL FRACTURE

  10. Others 23 % Static fracture 13% corrosion burst 3% SCC 5% TOTAL 242 SIMPLE FATIGUE 58% 77% FATIGUE CORROSIO FATIGUE ROLLING CONTACT FATIGUE 11 % Others 10 Thermal Fatigue 8 % Wire rope 8 Cast 15 90 % Stress concentration Welded part 77 242 Gear 18 Pulley,roll 28 Key, atc 56 Bolt 32

  11. MODE OF FRACTURE Mixed Mode I & II I & III

  12. FRACTURE MECHANICS PARAMETERS σy K = σvπ. a f (a/w) K = stress insity factor a = crack size f(a/w) = shape factor

  13. Fracture toghness • Kc is fracture toughness value/ nilai ketangguhan retak • K ~ Kc === patah/fracture • K < Kc == crack propagation/menuju patah a ~ ac (critical size)  patah Δ K = K max –K min K max = σ max V π. a f (a/w) K min = σ min V π. a f (a/w)

  14. Unstable III da/dN • Crack initiation • Propagation • Final/static fracture II Stable crack Kc properties Fracture toughness value I Δ Kth Δ K K

  15. Crack propagation (da/dN • PARIS LAW da/dN = C (Δ K)m Δ K = stress intensity range C , m = the material constant Δ K = K max – K min

  16. P da/dN (log scale) ΔP1>ΔP2>ΔP3 a ΔP3 ΔP2 CRACK PROPAGATION ΔP1 b da/dN = C (ΔK)m t a da dN N(cycles) ΔK (log scale) ΔK = Δσ (πa)^1/2 f(a) P R=0 R = -1 P max + ΔP t(time) - P min

More Related