1 / 10

ATtiny2313 Fuse Programming

CS-423 Dick Steflik. ATtiny2313 Fuse Programming. Whats a Fuse. Fuses are used to hold important configuration information for the MPU Not really a fuse, just a few really important bytes of memory 1 means unprogrammed, 0 means programmed unlike a fuse they can be reprogrammed

glyn
Download Presentation

ATtiny2313 Fuse Programming

An Image/Link below is provided (as is) to download presentation Download Policy: Content on the Website is provided to you AS IS for your information and personal use and may not be sold / licensed / shared on other websites without getting consent from its author. Content is provided to you AS IS for your information and personal use only. Download presentation by click this link. While downloading, if for some reason you are not able to download a presentation, the publisher may have deleted the file from their server. During download, if you can't get a presentation, the file might be deleted by the publisher.

E N D

Presentation Transcript


  1. CS-423 Dick Steflik ATtiny2313Fuse Programming

  2. Whats a Fuse • Fuses are used to hold important configuration information for the MPU • Not really a fuse, just a few really important bytes of memory • 1 means unprogrammed, 0 means programmed • unlike a fuse they can be reprogrammed • on the ATtiny2313 there are 3 fuse bytes • low byte (lbyte)‏ • high byte (hbyte)‏ • extended byte (ebyte)‏

  3. Low Byte • 7 (0) – CKDIV8 – Divide Clock by 8 • 6 (1) – CKOUT – Output clock on CKOUT pin • 5 (1) – SUT1 – Select start-up time • 4 (0) – SUT0 – Select start-up time • 3 (0) – CKSEL3 – Select clock source • 2 (1) – CKSEL2 – Select clock source • 1 (0) – CKSEL1 – Select clock source • 0 (0) – CKSEL0 – Select clock source

  4. Note: Default Low Byte • Default Low Byte value is 0x64 • Divide clock by 8 • Internal RC Oscillator (8 MHz)‏ • This means default speed is 1 MHz

  5. Select Start-up time • Default value (1 0) results in Maximum start-up time

  6. Clocking Options- CKSEL 3..0 • 0000 – External Clock • 0010 – Internal RC Oscillator (4 Mhz)‏ • 0100 – Internal RC Oscillator (8 Mhz)‏ • 0110 – Watchdog Oscillator (128 KHz)‏ • 1000-1111 – External Chrystal/Ceramic Resonator • 0001,0011,0101,0111 - Reserved

  7. High Byte • 7 (1) – DWEN – debugWIRE Enable • 6 (1) – EESAVE – EEPROM is preserved during chip erase • 5 (0) – SPIEN – SPI Enable • 4 (1) – WDTON – Watchdog timer always on • 3 (1) – BODLEVEL2 – brownout detector trig level • 2 (1) – BODLEVEL1 – brownout detector trig level • 1 (1) – BODLEVEL0 – brownout detector trig level • 0 (1) – RSTDISBL – External Reset disable

  8. Brownout Detection Trigger Level • The ATtiny2313 has an On-chip Brown-out Detection circuit that monitors Vcc to fixed trigger levels • Programmed by BODLEVEL 2..0 Fuses 1 1 1 BOD disabled 1 1 0 1.8 v 1 0 1 2.7 v 1 0 0 4.3 v

  9. Extended Byte • 7 (1) – not used • 6 (1) – not used • 5 (1) – not used • 4 (1) – not used • 3 (1) – not used • 2 (1) – not used • 1 (1) – not used • 0 (1)– SELFPRGEN – Self programming Enable

  10. Fuse Programming • Can be done through the Studio GUI if you are using the Atmel programmer • AVRDUDE & Parallel Port programmer • Use the -U option as follows: Avrdude -p Attiny2313 -c dapa -v -U lfuse:w:0xE4

More Related