1 / 27

BIW06, FNAL, May 1~4, 2006

Commissioning of the FPGA-Based Transverse and Longitudinal Bunch-by-Bunch Feedback System for Taiwan Light Source Kuo-Tung Hsu on behalf of the feedback team NSRRC Hsinchu 30076, Taiwan May 2, 2006. BIW06, FNAL, May 1~4, 2006. Outline. I. Introduction II. Feedback Processor

gelsey
Download Presentation

BIW06, FNAL, May 1~4, 2006

An Image/Link below is provided (as is) to download presentation Download Policy: Content on the Website is provided to you AS IS for your information and personal use and may not be sold / licensed / shared on other websites without getting consent from its author. Content is provided to you AS IS for your information and personal use only. Download presentation by click this link. While downloading, if for some reason you are not able to download a presentation, the publisher may have deleted the file from their server. During download, if you can't get a presentation, the file might be deleted by the publisher.

E N D

Presentation Transcript


  1. Commissioning of the FPGA-Based Transverse and Longitudinal Bunch-by-Bunch Feedback System for Taiwan Light Source Kuo-Tung Hsu on behalf of the feedback team NSRRC Hsinchu 30076, Taiwan May 2, 2006 BIW06, FNAL, May 1~4, 2006

  2. Outline I. Introduction II. Feedback Processor III. Transverse Feedback System IV. Longitudinal Feedback System V. Summary BIW06, FNAL, May 1~4, 2006

  3. I. Introduction • TLS is a 1.5 GeV light source. • Dedication in October 1993. • Instabilities are severe in the operation of last decade. • SRF upgrade in Dec. 2004. • Routine top-up operation is started from Oct. 2005. • FPGA-based transverse and longitudinal feedback • system are deployed in Dec. 2005 and Feb. 2006. BIW06, FNAL, May 1~4, 2006

  4. II. FPGA Based Feedback Processor • Adopted form the design of SPring-8. • Minor modification in FPGA code. • USB 2.0 interface is supported. • Up to 20 taps FIR filter is supported for transverse feedback. • Up to 50 taps FIR filter is supported for longitudinal feedback. • Up to 10 (20) decimation factor is supported. => only useful for longitudinal feedback. BIW06, FNAL, May 1~4, 2006

  5. Structure of the Feedback Processor 12 Bit 12 Bit 12 Bit 12 Bit FIFO FIFO FIFO FIFO FIR Filter* FIR Filter* FIR Filter* FIR Filter* DAC 500 MS/sec ADC 125 MS/sec FPGA: Xilinx VirtexII Pro XC2VP70-6FF1517C 4:1 MUX 12 Bit Delay FIFO DDR F/F FIR Filter* 12 Bit DDR F/F 20-tap FIR Filter 20-tap FIR Filter 12 Bit DDR F/F 50-tap FIR Filter 12 Bit 4:1 MUX Delay FIFO DDR F/F Delay Adj. 4:1 MUX 12 Bit Delay FIFO DDR F/F x2 to 249.83 MHz 499.65 MHz fRF/4 = 124.91 MHz DDR SDRAM, 128 Mega Samples X 4 PLL BIW06, FNAL, May 1~4, 2006

  6. Feedback System Environment • Linux/PC : • * Feedback Processor Linux Driver support • USB 2.0 access • * Matlab interface • Control database interface • Feedback processor register access • Captured bunch oscillation data access • Feedback filter design • Data analysis • * Control console Linux (CentOS Distribution) Control Network USB 2.0 Interface => Register access => Memory access Transverse Kicker Transverse and Longitudinal Pickup Bunch Oscillation Detector Back-end Electronic and Power Amplifiers Feedback Processor Longitudinal Kicker BIW06, FNAL, May 1~4, 2006

  7. III. Transverse Feedback System • 1995 Commissioning of the analog feedback system. • * Only vertical instability is a problem. • * Longitudinal instability is severe. • Second tuner was introduced to RF cavities to shift HOM frequency. • * Longitudinal instability is still severe. • * Transverse instability can be controlled by optimized position of the second tuner. • 2004.12 SRF put into operation. • * Both horizontal and vertical instability are strong. • * Difficult control by over compensatedchromaticity. • 2005.04 Analog transverse feedback loop is put back into service again • * Both plane instability was suppressed, however, tune dependence is strong. It is not easy to operate the machine with 0.1% flux • stability. BIW06, FNAL, May 1~4, 2006

  8. 2005.10.12 Start top-up operation @ 200 mA 2005.11.29 Commissioning of the new transverse feedback system. * To solve the sensitivity problem of tune dependence. * To provide better damping for high current operation. * Increase injection efficiency by reduce chromaticity. => High injection efficiency is essential for top-up operation. 2005.11.30 New digital transverse feedback system commissioning and put into service immediately. 2005.12 Start top-up operation at 300 mA BIW06, FNAL, May 1~4, 2006

  9. Block Diagram of the New Transverse Feedback System Feedback Processor D 4 ns A B # 1, 5, 9, .. 197 156 MHz LPF 2 ns ADC 20tapFIR ch 1 C D 20 dB # 3, 7, 11, .. 199 ch 3 20tapFIR ADC # B DACs 933 MHz LPF LNA 4 ns Divider # 2, 6, 10, .. 198 46 dB ADC 20tapFIR ch 2 20 dB # 4, 8, 12, .. 200 Clock/4 = 124.913 MHz ch 4 # B ADC 20tapFIR Divider 2 Vp-p X 4 # A 124.913 MHz Clock/4 = 124.913 MHz Clock FPGA LVDS BBF Clock Generator Transverse Kicker 250 W fRF 499.654 MHz 20 dB 53 dB B 20 dB AR 250A250 20 dB D 20 dB 53 dB 10 KHz ~ 250 MHz BIW06, FNAL, May 1~4, 2006

  10. Layout of pickup & kicker R3 R2 R4 Location bx(m)by(m)nxny hx(m) R5 BPM1 11.3 5.4 4.876 3.018 0.033 R5 Kicker 4.5 2.7 5.572 3.232 0.397 Target Working Point (nx, ny) = (7.312, 4.168) Tunability Dn ~ 0.05 C = 120 m Trev = 400.2 ns Frev = 2.49827 MHz 80 nsec Feedback Electronics R5BPM1 (B - D) 150 nsec R5 R1 R6 Kicker (B - D) BIW06, FNAL, May 1~4, 2006

  11. Response of the Prototype FIR Filter Parameters of the Transverse Feedback System Target Tune Feedback Loop Tunability Working tune bandwidth (change in arbitrary way) nx: 716 kHz ~ 822 kHz (7.285 ~ 7.328) => dn > 0.04 ny: 400 kHz ~ 480 kHz (4.16 ~ 4.192) => dn > 0.03 Negative chromaticity Nominal setting (SF, SD) = (151 Amp, 124 Amp) => (SF, SD) = (121 Amp, 114 Amp) => Beam is still stable => (SF, SD) = (100 Amp, 100 Amp) => Beam is still stable However, beam loss suddenly when turn off the feedback loop BIW06, FNAL, May 1~4, 2006

  12. Beam spectrum observation – Feedback OFF and ON Beam spectrum observation (without longitudinal feedback) Feedback OFF Feedback ON BIW06, FNAL, May 1~4, 2006

  13. Snapshot of Synchrotron Radiation Beam Profile (w/o Longitudinal Feedback) Grow/Damp test results @ 300 mA Horizontal Loop Open Vertical Horizontal Vertical Modal Spectrum Loop Closed BIW06, FNAL, May 1~4, 2006

  14. Current Status of the Transverse Feedback System • Stable operation have been achieved in users shift. • Better than 10-3photon flux stability can be achieved routinely. • Various feedback filters will be tested in a short-term to probe the possibility to improve system performance. • Improve various components form operation point of views are under way. BIW06, FNAL, May 1~4, 2006

  15. IV. Longitudinal Feedback System • Longitudinal instability is serve during last decade operation of TLS. • Optimized the second tuner position and RF gap voltage modulation is the tools to deal this instability with the cost of large energy oscillation. • After SRF upgrade • Strength of the longitudinal is weaker than before. • Mode pattern are much simple. • Longitudinal feedback system are used to lift the residue instabilities. • 2006.01 New longitudinal kicker installed. • 2006.02.06 Longitudinal feedback system commissioning. BIW06, FNAL, May 1~4, 2006

  16. Adaptation of the SLS Longitudinal Kicker to the TLS LFB System • Modified from the DAΦNE and BESSY kickers (four ridged waveguide damper; nose cone) • Center frequency @ 1375 MHz, BW > 250 MHz • Highest shunt impedance ~ 1500 Ω • A few higher order modes are trapped in the structure and are damped by a hybrid TE/TM coupler • Successful operation of the SLS longitudinal kicker • Easy adaptation to the TLS storage ring with minor modifications (nearly rectangular 28 x 88 mm beam pipe elliptical, 38 x 80 mm beam pipe) • Variation of group delay across the operation bandwidth found (~ 600 ps) • Symmetrical excitation to minimize transverse kick due to field non-uniformity Summary of Measured Longitudinal Kicker Performance BIW06, FNAL, May 1~4, 2006

  17. Parameters of the Longitudinal Feedback System Response of the Prototype FIR Filter BIW06, FNAL, May 1~4, 2006

  18. Layout of pickup & kicker R3 ns ~ 0.0136 C = 120 m Trev = 400.2 ns frev = 2.49827 MHz fs = frev/4 = 625 kHz R2 R4 Feedback Electronics Beam Position Monitor (Energy Oscillation Detector) Power Amplifier R5BPM4 (A+B+C+D) R1 R5 Longitudinal Kicker (Energy Correct Kick) Longitudinal Kicker R6 BIW06, FNAL, May 1~4, 2006

  19. 30 dB 20 dB Block Diagram of the Longitudinal Bunch-by-Bunch Feedback System I-Tech’s RF Front-End Buffer and Delay Module S # 1, 5, 9, .. 197 A B ADC 50tapFIR 8 ns # 2, 6, 10, .. 198 D C X 3 ADC 50tapFIR DAC 6 ns 499.654 MHz # 3, 7, 11, .. 199 ADC 50tapFIR 4 ns # 4, 8, 12, .. 200 Clock/4 = 124.913 MHz ADC 50tapFIR X 4 2 ns Clock/4 = 124.913 MHz Clock FPGA 124.913 MHz LVDS BBF Clock Generator 499.654 MHz 200 W SSB Or QPSK Modulator 53 dB Longitudinal Kicker Milmega AS0814-250R 0.8 GHz ~ 1.4 GHz 1500 MHz (SSB) or 1375 MHz (QPSK) BIW06, FNAL, May 1~4, 2006

  20. SSB Modulator Beam Spectrum QPSK Modulator Sirenza STQ-2016 700-2500 MHz Direct Quadrature Modulator Phase Shifter MiniCircuits Amplifier 499.654 MHz RF Output Frequency Multiplier I Shut-down control Q Excitation On/Off Control AD8131 Differential Amplifier PULSAR QE-14-442 90o Hybrids (2~250 MHz) Monitor 0o Correction Signal USB or LSB Selection 90o BIW06, FNAL, May 1~4, 2006

  21. Temporal Behavior of Longitudinal Instability Build-up Loop Open 40 msec Longitudinal Instability Signal Loop Open 100 msec BIW06, FNAL, May 1~4, 2006

  22. Beam Phase and Beam Spectrum with Feedback Loop Open and Closed Beam Spectrum (Open-Loop vs. Closed-Loop) Filling Pattern Beam Phase w/o LFB Beam Phase w LFB 62.5 MHz peak is due to filling pattern with 16 nsec periodicity 2nd harmonic of 62.5 MHz Beam Spectrum Details w/o and w LFB BIW06, FNAL, May 1~4, 2006

  23. Longitudinal Grow/Damp Experiments @ 250 mA BIW06, FNAL, May 1~4, 2006

  24. Snapshot of the Synchrotron Radiation Beam Profile Streak Camera Observation One Turn Loop Open Loop Open Loop Open Loop Open One Turn Loop Closed Loop Closed -> Open -> Closed One Turn Loop Closed BIW06, FNAL, May 1~4, 2006

  25. Current Status of the Longitudinal Feedback System • Stable operation have been achieved in users shift. • Increase the beam brilliance at the results. • Various feedback filters will be try to improve system performance. • Improve aspect form operation point of views are same as transverse feedback system. BIW06, FNAL, May 1~4, 2006

  26. V. Summary • Two major upgraded have been completed recently for the TLS. • - SRF cavity • - Top-up operation • Transverse feedback system upgrade from analog to digital system in late 2005. • Longitudinal feedback system commissioning successful in early 2006. • Both the transverse and longitudinal feedback loop adopt the same feedback processor - SPring-8 designed feedback processor. • Modified SLS longitudinal kicker is used. • SLAC analysis code is adopted for transient signal analysis. • Both systems put into service immediately after commissioning. • Improved the system performance and functionality is on going. BIW06, FNAL, May 1~4, 2006

  27. Acknowledgements Many peoples contributed to this project directly or indirectly. Thanks for their help. T. Nakamura, K. Kobayashi (JASRI/SPring-8) M. Dehler (SLS/PSI) M. Tobiyama (KEKB) J. Fox, D. Teytelman, S. Prabhakar(SLAC) J. Seebek (SSRL), G. Strover, J. Byrd (LBNL) Thank You for Your Attention ! BIW06, FNAL, May 1~4, 2006

More Related