1 / 18

Test of Pixel Sensors for the CMS experiment

Test of Pixel Sensors for the CMS experiment. Amitava Roy. Purdue University. Pixel Sensors. The CMS experiment at the LHC will have a silicon pixel detector as its innermost tracking device. 2 barrels, 17(27) Mpixels. 4 forward disks, 12 Mpixels.

emmy
Download Presentation

Test of Pixel Sensors for the CMS experiment

An Image/Link below is provided (as is) to download presentation Download Policy: Content on the Website is provided to you AS IS for your information and personal use and may not be sold / licensed / shared on other websites without getting consent from its author. Content is provided to you AS IS for your information and personal use only. Download presentation by click this link. While downloading, if for some reason you are not able to download a presentation, the publisher may have deleted the file from their server. During download, if you can't get a presentation, the file might be deleted by the publisher.

E N D

Presentation Transcript


  1. Test of Pixel Sensors for the CMS experiment Amitava Roy Purdue University

  2. Pixel Sensors • The CMS experiment at the LHC will have a silicon pixel detector as its innermost tracking device. 2 barrels, 17(27) Mpixels 4 forward disks, 12 Mpixels NP 2000 A. Roy

  3. How does a Silicon detector works? • A detector has to be fully depleted! • What is depletion? • Giving enough reverse bias • voltage so that no free carriers • are available. No more a diode • now. It’s a resistor! • Why? • In fully depleted condition, if a • particle goes through the detector • it will make electron and hole • pair. They are attracted to the • opposite terminals and get • collected - we get a signal! P + + + + + + + N+ - - - - - - - Hole and free electron free region Newly generated electron and hole pair Particle - + - + NP 2000 A. Roy ROC

  4. How does CMS pixel looks? N N+ P+ • It’s N+ on N! Not a diode! • And it has 11 Guard rings (what’s that?) NP 2000 A. Roy

  5. It’s going to be a Diode later! • In LHC it will be a harsh • radiation environment. In 6 years • of running, fluence will be • 6x1014 /cm2 at r=7cm • This radiation make the N to P! • Nuclear interaction with the • incoming particle, Si => 25Mg. • A considerable concentration of is • 25Mg is achieved. • Magnesium is a donor. That will make the N to P! NP 2000 A. Roy

  6. What does the Guard ring guard? SiO2 V • To protect from outer environment detector is covered with SiO2. • SiO2 traps electrons at the surface that causes a high voltage drop in a small area. • High electric field - silicon breaks down. • To maintain a uniform voltage drop guard rings are used! N P+ N+ Breakdown prone area Trapped electrons V NP 2000 A. Roy

  7. What voltage we need? Neutron irradiation Proton irradiation • So we have to operate at 400 V NP 2000 A. Roy

  8. No full depletion! • We are going to operate in 300V - partial depletion. • We will be collecting the electrons still! NP 2000 A. Roy

  9. Wafers • We received sensors from two vendors. • 3 wafers from CSEM • 300 mm. • 2 wafers from Sintef 275 mm. NP 2000 A. Roy

  10. Single and double sided measurement • Measurement can be • done from P+ side • only! N P+ N+ A A NP 2000 A. Roy

  11. Guard Ring • Guard ring design good enough • to have Vbreakdown > 1000V! NP 2000 A. Roy

  12. Pixels • Vdepletion~ 155 V • Some pixels has metal • on top, some doesn’t. • There are 8 different • p-stop designs. • Vbreakdown between • 200-800 volts. Metalized Non-metalized NP 2000 A. Roy

  13. Pixels A,B,C - not metalized D,E,F,G,H - metalized • Metalized pixels have higher • breakdown voltage. NP 2000 A. Roy

  14. Pixels Design G Design A • Among 8 different type of p-stops design, design A, F and G • have higher breakdown voltage. Design F NP 2000 A. Roy

  15. Best Pixels • Design A, F and G with metal • on top have the best • performances. Vbreakdown ~ 800V NP 2000 A. Roy

  16. Interpixel resistance I1 • We took a pixel well • inside the array so that • it is isolated from the • n-ring • R=V/(I2-I1) N N+ P+ I2 V NP 2000 A. Roy

  17. Interpixel resistance • V at the center pixel shows • that p-stop start kicking in • after 150 volts. A sign that the • whole pixel array is getting • biased. NP 2000 A. Roy

  18. Conclusions • Single sided probing is possible. • Guard Ring design is good for operational voltage > 1000V • We optimized the p-stop design. Design A,F and G breaks • down around 800V, far above 300V, the operating voltage in • LHC. • P-stop design gives high resistance to isolate the pixels after • depletion voltage. NP 2000 A. Roy

More Related