1 / 20

BMAC - Versatile Low Power Media Access for Wireless Sensor Networks

BMAC - Versatile Low Power Media Access for Wireless Sensor Networks. Introduction. What is BMAC? A configurable MAC protocol for WSNs Small core Factors out higher-level functionality Energy efficient Goals Low Power operation Effective collision avoidance Simple and predictable

edr
Download Presentation

BMAC - Versatile Low Power Media Access for Wireless Sensor Networks

An Image/Link below is provided (as is) to download presentation Download Policy: Content on the Website is provided to you AS IS for your information and personal use and may not be sold / licensed / shared on other websites without getting consent from its author. Content is provided to you AS IS for your information and personal use only. Download presentation by click this link. While downloading, if for some reason you are not able to download a presentation, the publisher may have deleted the file from their server. During download, if you can't get a presentation, the file might be deleted by the publisher.

E N D

Presentation Transcript


  1. BMAC - Versatile Low Power Media Access for Wireless Sensor Networks

  2. Introduction • What is BMAC? • A configurable MAC protocol for WSNs • Small core • Factors out higher-level functionality • Energy efficient • Goals • Low Power operation • Effective collision avoidance • Simple and predictable • Small code size and RAM usage • Tolerable to changing RF/networking conditions • Scalable to large numbers of nodes

  3. MAC design approaches • Traditional (e.g. SMAC) • “Black-box” design • Users pre-configure duty cycle • Applications rely on S-MAC to adjust its operation as things change • Designed (and optimized) for a set of workloads that might not always be applicable • Minimalistic (BMAC) • Small core functionality: media access control • RTS/CTS, ACKs, etc are considered higher layer functionality (services) • Applications can turn them on and off • More flexible and more tunable

  4. BMAC basics • Use long preambles (010101010) • Sleeping nodes will eventually wake up, check the channel and detect that it is active (preamble) and then begin to listen • It is required that the preamble be long enough so that all nodes will be awake for the data transmission.

  5. BMAC trade-off If the time between channel samples is long, then the preamble must be very long. The preamble must last about as long as the time between checking if the channel is busy The amount of energy used transmitting long preambles depends on how often data is sent. E.g., if data must be sent only once a day, it might be ok to have a preamble that last an hour, since that would allow a very long time between checking the channel. Letting PT be the power used during transmission of a preamble TP be the duration of the preamble R the rate of sending data (pkts/sec) Echeck the energy required to check the channel Then: Energy for transmitting = Energy for receiving = Energy for forwarding = Optimal value of TP

  6. BMAC trade-off If the time between channel samples is long, then the preamble must be very long. The preamble must last about as long as the time between checking if the channel is busy The amount of energy used transmitting long preambles depends on how often data is sent. E.g., if data must be sent only once a day, it might be ok to have a preamble that last an hour, since that would allow a very long time between checking the channel. Letting PT be the power used during transmission of a preamble TP be the duration of the preamble R the rate of sending data (pkts/sec) Echeck the energy required to check the channel Then: Energy for transmitting = Energy for receiving = Energy for forwarding = Optimal value of TP =

  7. LPL check interval Sensor sample period – controls the packet rate • Single-hop application doing periodic data sampling • Sampling rate (traffic pattern) defines optimal check interval • Check interval • Too small: energy wasted on idle listening • Too large: energy wasted on transmissions (long preambles) • In general, it’s better to have larger preambles than to check more often! Time between listening (checking if the channel is idle)

  8. LPL and neighborhood size • More neighbors: more transmissions • More time spent receiving packets • Less time left to go to sleep • To find the best check interval • Set the reporting rate • Estimate neighborhood size • Best result: check interval that gives lowest effective duty cycle

  9. Energy vs Latency S-MAC Default Configuration B-MAC Default Configuration • 10-hop network • Source sends a 100-byte packet every 10 seconds • SMAC: change the default config • BMAC: choose optimal check interval • SMAC again performs worse... • Reason: sync packets, probability of multiple schedules---less time to sleep

  10. Throughput vs power consumption • 10 nodes in a neighborhood • Data must arrive within 10 seconds • Average power consumption per node • Low data rates: SMAC is better • Very low duty cycle • Power vs throughput • SMAC: linear • BMAC: sub-linear • Reason: SMAC duty cycle must increase • More active periods, more SYNC periods • BMAC: larger preambles at low throughput, progressively becoming smaller

  11. Experimental results: throughput • “BMAC is about 4.5 faster than SMAC-unicast” • Not as fast when ACK or RTS/CTS is used • No combined results... • Differences less pronounced as # of nodes increases • Another issue: BMAC has CCA, thus it backs off less frequently (and perhaps the backoff timer is faster)

  12. Clear Channel Assessment MAC must accurately determine if channel is clear Need to tell what is noise and what is a signal Ambient noise is prone to environmental changes BMAC solution: ‘software automatic gain control’ initialization Signal strength samples taken when channel is assumed to be free so that a noise floor is found. Check channel Samples go in a FIFO queue (sliding window) Median of FIFO is added to an EWMA filter. When the EWMA filter exceeds a threshold, then it is assumed that the channel is active. The median filter is known to be robust to impulse noise/outliers EWMA is not a particularly good way to find a change of state. A better approach is based on statistical change-point detection (see next slide) Once noise floor is established, a TX requests starts monitoring RSSI from the radio

  13. Change point detection If the likelihood ratio is small, then 1. it is unlikely that what we observed could have occured and the change, and 2, it is likely that what was observed occured without the change likelihood ratio typical likelihood ratio typical log-likelihood ratio But, if the distributions are Gaussian, then this can be changed into a cummulative summation if Sk >Thresh, then the change has occurred. This is the optimal approach in terms of detecting a change fastest with a given false-alarm rate

  14. CCA: single-sample thresholding vs outlier detection Common approach: take single sample, compare to noise floor Large number of false negatives BMAC: search for outliers in RSSI If a sample has significantly lower energy than the noise floor during the sampling period, then channel is clear

  15. CCA results 0=busy, 1=clear Packet arrives between 22 and 54 ms Single-sample thresholding produces several false ‘busy’ signals

  16. Low Power Listening Goal: minimize listen cost Principles Node periodically wakes up, turns radio on and checks channel Wakeup time fixed “Check time” variable If energy is detected, node powers up in order to receive the packet Node goes back to sleep If a packet is received After a timeout Preamble length matches channel checking period No explicit synchronization required Noise floor estimation used to detect channel activity during LPL

  17. Radio powerup sequence of operations Goals Minimize time radio is on Minimize number of times radio gets started Minimize sampling time (stage e)

  18. Conlcusions • BMAC appears to be better than SMAC • Easier to tune • Has better channel assessment • Doesn’t use explicit sync packets • Doesn’t use RTS/CTS/ACK if it doesn’t have to • Is smaller and less complex • Are large preambles always good? • Not sure, but: • They do mention ‘cyclic packet transmissions’ • They can be turned off: • Enable LPL • Send first packet, disable LPL • Send remaining packets in a big burst • Re-enable LPL

More Related