F/A-18 CVRS-FLIR-BDA PROTOTYPE
Download
1 / 9

F/A-18 CVRS-FLIR-BDA PROTOTYPE - PowerPoint PPT Presentation


  • 105 Views
  • Uploaded on

F/A-18 CVRS-FLIR-BDA PROTOTYPE. Chief Warrant Officer Jim May III VMFA-251 Avionics Officer USS Roosevelt (CVN 71), JDial - 6239 Email - [email protected] 18 December 2001 w/Rev 1 (25 Apr 2002). F/A-18 CVRS-FLIR-BDA MOD PROTOTYPE. PROS

loader
I am the owner, or an agent authorized to act on behalf of the owner, of the copyrighted work described.
capcha
Download Presentation

PowerPoint Slideshow about ' F/A-18 CVRS-FLIR-BDA PROTOTYPE' - dolan-macias


An Image/Link below is provided (as is) to download presentation

Download Policy: Content on the Website is provided to you AS IS for your information and personal use and may not be sold / licensed / shared on other websites without getting consent from its author.While downloading, if for some reason you are not able to download a presentation, the publisher may have deleted the file from their server.


- - - - - - - - - - - - - - - - - - - - - - - - - - E N D - - - - - - - - - - - - - - - - - - - - - - - - - -
Presentation Transcript

F/A-18 CVRS-FLIR-BDA PROTOTYPE

Chief Warrant Officer Jim May III

VMFA-251 Avionics Officer

USS Roosevelt (CVN 71), JDial - 6239

Email - [email protected]

18 December 2001

w/Rev 1 (25 Apr 2002)


F/A-18 CVRS-FLIR-BDA MOD PROTOTYPE

  • PROS

    • Increases current capabilities of the Left (Fwd) CVRS Recorder from 2 recording options (LDDI and HUD) to 3 options (LDDI, HUD and FLIR).

    • Dual recording of FLIR provides redundancy for FLIR BDA.

    • Eliminates problems experienced with current DDI/Camera configuration (Glare, Poor Lighting, Camera Alignment, DDI Failure, Etc.).

    • Auto-HUD override switch added to allow the pilot to select whether the the HUD will override the LDDI or HUD during weapon release functions.

    • Easy assembly, 90% of the work should be able to be done right in the work center (Mod could be in a kit form for the fleet, just pop it in).

    • Mod would be easy to remove, for temporary testing/installs.

    • Should be easy to get flight clearance, judging from what was previously recommended (pulling windscreens and cheek panels).

    • Minimal Cost.

  • CONS

    • The raw Black/White FLIR video may not really gain much for quality.

    • Need an old monitor or scan rate converter to view the video with the current playback station configuration.


F/A-18C AFT UPPER EQUIPMENT BAY

FORWARD COCKPIT

LEFT CAMERA

RIGHT CAMERA

SW PANEL

LDDI/HUD/FLIR

RIGHT (AFT) RECORDER

LEFT (FWD) RECORDER

OTHER STATION VIDEOS

(SIMPLIFIED)

LDDI

HUD

FLIR

VIDEO CONTROLLER

RDDI

DOOR 14R

DOOR 13R

LEGEND

LEFT CVRS VIDEO (ORIGINAL)

LEFT CVRS VIDEO (ADDED)

RIGHT CVRS VIDEO

OTHER VIDEO FEEDS

SMS

F/A-18 CVRS-FLIR-BDA MOD PROTOTYPE


LEFT CAMERA

INPUT/OUTPUT MATRIX

OPTION

A - 26

A - 28

A - 34

INPUT

OUTPUT

SMS

(FLIR)

LDDI

YES

YES

NO

B - 2

A - 20/21

HUD

NO

NO

NO

B - 8

A - 20/21

FLIR

YES

NO

NO

B - 1

A - 20/21

LEFT (FWD) RECORDER

SW PANEL

LDDI/HUD/FLIR

OVER THE SHOULDER (FLT TEST) CAMERA JACK

HUD

FLT TEST

NO

NO

YES

A - 32/33

A - 20/21

2 8 1

79P-L042B

VIDEO CONTROLLER

32/33 34 26 28 20/21

LEGEND

LEFT CVRS VIDEO (ORIGINAL)

LEFT CVRS VIDEO (ADDED)

CONTROL WIRING

79P-L042A

F/A-18 CVRS-FLIR-BDA MOD PROTOTYPE

  • VIDEO CONTROLLER CAPABILITES

    • The Video Controller is shown wired with the capability of 4 selectable inputs (LDDI, HUD, FLIR and Flight Test) to 1 Output (FWD Recorder).


61J-L272

79P-L042B

(PIN 1)

61P-F272

61P-F001F (J6)

F/A-18 CVRS-FLIR-BDA MOD PROTOTYPE

  • FLIR VIDEO SPLITTER CABLE

  • Allows the FLIR input video to go to both the SMS Computer and the Video Controller:

    • The short legs split the regular FLIR input cable to the SMS J/P6 (61J/P-F001F).

    • The long leg routes to the NAVFLIR bulkhead jack (61J-L272) in 13R, the current connector (61P-F272) will be temporarily stowed.

    • Another short cable will run from 61J-L272 in the Aft Upper Equipment Bay to the Video Controller connector (79P-L042B Pin 1), the current connector (61J-L272) in the Aft Upper Equipment Bay will also be temporarily stowed.

    • This temp install utilizes the NAVFLIR bulkhead connectors for easy access into the pressurized cockpit area.

    • This is not intended as a permanent wire routing solution.

    • No actual aircraft wiring is affected.

F/A-18C AFT UPPER EQUIPMENT BAY

VIDEO CONTROLLER

15”

DOOR 14R

DOOR 13R

8’

MC2

FCCB

TACAN

CLC

SMS

6”


FORWARD COCKPIT

LH LOWER INSTRUMENT PANEL

(VIDEO SELECT SW) (HUD MODE SW)

FLIR HUD LDDI ORIDE AUTO

5 2 2

4 6 1 3 3

SR42E22

SR42F22

SR43A22

7 6 5

61J-L272

52P/J-H320

79P-L042A

S002

79P-L042B

F/A-18C AFT UPPER EQUIPMENT BAY

26 28 27

1

VIDEO CONTROLLER

15”

F/A-18 CVRS-FLIR-BDA MOD PROTOTYPE

  • VIDEO SELECT SWITCH

  • Allows pilot to select LDDI/HUD/FLIR.

    • Restore aircraft wiring similar to the way it was prior to the AFC-207, per 770-500 WP6 02 Pg 6 and WDM-010 D401. Remove splice (S002) and reconnect wires to only connect 79P-L042A pins 26/28 to 52P-H320 pins 7/6 respectfully.

    • Install the new DP/DT/3POS switch and rewire panel (79S-H053), similar to 770-300 WP14 02, Pg 7.

    • Factory Installed CVRS (Lot 17 and Up) aircraft will require the Blue Wire (52P-H320 Pin 7 to 79P-L042A Pin 26) to be installed. All other aircraft have the required wiring in place.

  • HUD MODE SWITCH (SHOWN IN RED)

  • Allows pilot to select either Auto-HUD or O/R-HUD.

    • AUTO provides the common functionality to allow the HUD to automatically record vice the selected LDDI or FLIR, during weapon release functions.

    • ORIDE allows the pilot to disable the the Auto-HUD function and force the recorder to record the selected feature (LDDI and FLIR), during weapon release functions.

    • Reuse the old Video Select Switch (DP/ST/2POS) from above.


FLIR VIDEO SPLITTER CABLE ASSEMBLY

SHORT FLIR VIDEO FEED CABLE ASSEMBLY

LH LOWER INSTRUMENT PANEL (ORIGINAL)

LH LOWER INSTRUMENT PANEL (NEW/MOCK-UP)

F/A-18 CVRS-FLIR-BDA MOD PROTOTYPE


F/A-18 CVRS-FLIR-BDA MOD PROTOTYPE

  • PARTS LIST - All parts are available in the current Tech Manuals and Supply System:

  • 5935-01-330-9219 74868 82-5772-4 $40.58 61P-F001F CONNECTOR

  • 5935-01-282-2058 14949 BJ371 $26.36 61J-F001F RECEPTACLE

  • 5935-01-084-6353 95712 31-33485-7 $80.71 61P-F272 CONNECTOR

  • 5935-01-339-6592 95712 31-33546-17 $96.77 61J-L272 RECEPTACLE

  • 5999-01-339-1071 77820 21-33198-4 $67.35 79P-L042B PIN

  • 6145-01-317-9648 76301 5M2142-001 $1.98/FT TRIAX WIRE TYPE 880 (9 FT)

  • 6145-01-317-9648 76301 5M2559-001 $1.98/FT TRIAX WIRE TYPE 567 (15 IN)

  • 5930-01-125-5843 96906 MS90311-711 $27.29 DP/DT/3POS SWITCH

  • 5970-00-812-2967 03640 6086085-10 $0.39/FT 1”-0.5” HEATSHRINK (1 FT)

  • N/A N/A MULTI *EST/MIN MISC ITEMS

  • TOTAL ESTIMATED PARTS COST $375.00

  • 5930-00-914-6458 96906 MS90310-231 #$11.86 SP/ST/2POS SWITCH

  • 1680-01-478-6331 8V413 E6-120HME %$15.00 8MM (ME) VIDEO TAPE

  • NOTES/REMARKS:

  • * - COMMON SHOP ITEMS (I.E. SOLDER, TAPE, SPLICE) ARE NOT INCLUDED DUE TO NEGLIGIBLE COST, AVAILABILITY AND NATURE OF REQUEST

  • # - NO COST, REUSABLE FROM PREVIOUS CONFIGURATION (FOR AUTO-HUD OVERRIDE SWITCH)

  • % - OPTIONAL

  • - PRICES FROM FEDLOG


F/A-18 CVRS-FLIR-BDA MOD PROTOTYPE

  • SUPPORTING DATA

    • Prototype Request Message (DTG - 152200Z FEB 01 )

    • Flight Clearance Request Message (DTG - 240752Z APR 02)

    • LH Lower Instrument Panel Photos


ad