1 / 19

Lecture 21

Lecture 21. OUTLINE The MOSFET (cont’d) P-channel MOSFET CMOS inverter analysis Sub-threshold current Small signal model Reading : Pierret 17.3; Hu 6.7, 7.2. P-Channel MOSFET. The PMOSFET turns on when V GS < V T Holes flow from SOURCE to DRAIN

Download Presentation

Lecture 21

An Image/Link below is provided (as is) to download presentation Download Policy: Content on the Website is provided to you AS IS for your information and personal use and may not be sold / licensed / shared on other websites without getting consent from its author. Content is provided to you AS IS for your information and personal use only. Download presentation by click this link. While downloading, if for some reason you are not able to download a presentation, the publisher may have deleted the file from their server. During download, if you can't get a presentation, the file might be deleted by the publisher.

E N D

Presentation Transcript


  1. Lecture 21 OUTLINE The MOSFET (cont’d) • P-channel MOSFET • CMOS inverter analysis • Sub-threshold current • Small signal model Reading: Pierret 17.3; Hu 6.7, 7.2

  2. P-Channel MOSFET • The PMOSFET turns on when VGS < VT • Holes flow from SOURCE to DRAIN  DRAIN is biased at a lower potential than the SOURCE • In a CMOS technology, the PMOS & NMOS threshold voltages are usually symmetric about 0, i.e.VTp = -VTn VG • VDS < 0 • IDS < 0 • |IDS| increases with • |VGS - VT| • |VDS| (linear region) VS VD GATE ID P+ P+ N VB EE130/230M Spring 2013 Lecture 21, Slide 2

  3. Long-Channel PMOSFET I-V • Linear region: • Saturation region: m = 1 + (3Toxe/WT) is the bulk-charge factor EE130/230M Spring 2013 Lecture 21, Slide 3

  4. VDD S G D VOUT VIN D G S CMOS Inverter: Intuitive Perspective SWITCH MODELS CIRCUIT VDD VDD Rp VOUT = 0V VOUT = VDD Rn Low static power consumption, since one MOSFET is always off in steady state VIN = VDD VIN = 0V EE130/230M Spring 2013 Lecture 21, Slide 4

  5. Voltage Transfer Characteristic N: sat P: sat VOUT N: off P: lin C VDD N: sat P: lin B D E A N: lin P: sat N: lin P: off 0 VIN VDD 0 EE130/230M Spring 2013 Lecture 21, Slide 5

  6. increasing VIN VDSp= - VDD VDSp= 0 CMOS Inverter Load-Line Analysis – VGSp=VIN-VDD + VIN= VDD+ VGSp – VDSp=VOUT-VDD + VOUT= VDD+ VDSp IDn=-IDp VIN= 0 V VIN= VDD IDn=-IDp increasing VIN VOUT=VDSn 0 VDD 0 EE130/230M Spring 2013 Lecture 21, Slide 6

  7. Load-Line Analysis: Region A – VGSp=VIN-VDD + – VDSp=VOUT-VDD + IDn=-IDp VIN VTn IDn=-IDp VOUT=VDSn 0 VDD 0 EE130/230M Spring 2013 Lecture 21, Slide 7

  8. Load-Line Analysis: Region B – VGSp=VIN-VDD + – VDSp=VOUT-VDD + IDn=-IDp IDn=-IDp VDD/2> VIN> VTn VOUT=VDSn 0 VDD 0 EE130/230M Spring 2013 Lecture 21, Slide 8

  9. Load-Line Analysis: Region D – VGSp=VIN-VDD + – VDSp=VOUT-VDD + IDn=-IDp IDn=-IDp VDD– |VTp| > VIN > VDD/2 VOUT=VDSn 0 VDD 0 EE130/230M Spring 2013 Lecture 21, Slide 9

  10. Load-Line Analysis: Region E – VGSp=VIN-VDD + – VDSp=VOUT-VDD + IDn=-IDp VIN > VDD– |VTp| IDn=-IDp VOUT=VDSn 0 VDD 0 EE130/230M Spring 2013 Lecture 21, Slide 10

  11. MOSFET Effective Drive Current, IEFF M. H. Na et al., IEDM Technical Digest, pp. 121-124, 2002 CMOS inverter chain: VDD V2 IH + IL V1 V2 V3 V3 tpLH IEFF = VDD/2 2 tpHL V1 TIME IDsat VIN = VDD CMOS inverter: VDD S IH D NMOS DRAIN CURRENT VOUT VIN D VIN = ½VDD S GND IL 0.5VDD VDD NMOS DRAIN VOLTAGE = VOUT EE130/230M Spring 2013 Lecture 21, Slide 11

  12. Propagation Delay, td VDD CMOS inverter chain: Voltage waveforms: VDD td is reduced by increasing IEFF and reducing load capacitance C EE130/230M Spring 2013 Lecture 21, Slide 12

  13. Sub-Threshold Current • For |VG| < |VT|, MOSFET current flow is limited by carrier diffusion into the channel region. • The electric potential in the channel region varies linearly with VG, according to the capacitive voltage divider formula: • As the potential barrier to diffusion increases linearly with decreasing VG, the diffusion current decreases exponentially: EE130/230M Spring 2013 Lecture 21, Slide 13

  14. Sub-Threshold Swing, S log ID NMOSFET Energy Band Profile n(E)  exp(-E/kT) Inverse slope is subthreshold swing, S [mV/dec] increasing E Source increasing VGS VGS Drain 0 VT distance EE130/230M Spring 2013 Lecture 21, Slide 14

  15. VT Design Trade-off • Low VT is desirable for high ON current: IDsat (VDD- VT) 1 <  < 2 • But high VT is needed for low OFF current: log ID Low VT • VT cannot be aggressively reduced! High VT IOFF,low VT IOFF,high VT VGS 0 EE130/230M Spring 2013 Lecture 21, Slide 15

  16. How to minimize S? EE130/230M Spring 2013 Lecture 21, Slide 16

  17. MOSFET Small Signal Model • Conductance parameters: A small change in VG or VDS will result in a small change in ID low-frequency: high-frequency: EE130/230M Spring 2013 Lecture 21, Slide 17

  18. Parasitic Components EE130/230M Spring 2013 Lecture 21, Slide 18

  19. MOSFET Cutoff Frequency, fT The cut-off frequency fT is defined as the frequency when the current gain is reduced to 1. • Higher MOSFET operating frequency is achieved by decreasing the channel length L vGhere is ac signal CG is approximately equal to the gate capacitance,  W L Cox input current = output current = At the cutoff frequency (wT= 2pfT): EE130/230M Spring 2013 Lecture 21, Slide 19

More Related