1 / 22

The bigger picture: ceramic (CMC) metal (MMC) natural polymer (PMC)

The bigger picture: ceramic (CMC) metal (MMC) natural polymer (PMC). John Summerscales. Upper continuous operation temperature. from Hancox & Phillips, ICME-2, 1985. Residual stresses. CMC and MMC are often manufactured at high-temperatures

Download Presentation

The bigger picture: ceramic (CMC) metal (MMC) natural polymer (PMC)

An Image/Link below is provided (as is) to download presentation Download Policy: Content on the Website is provided to you AS IS for your information and personal use and may not be sold / licensed / shared on other websites without getting consent from its author. Content is provided to you AS IS for your information and personal use only. Download presentation by click this link. While downloading, if for some reason you are not able to download a presentation, the publisher may have deleted the file from their server. During download, if you can't get a presentation, the file might be deleted by the publisher.

E N D

Presentation Transcript


  1. The bigger picture:ceramic (CMC) metal (MMC) natural polymer (PMC) John Summerscales

  2. Upper continuousoperation temperature from Hancox & Phillips, ICME-2, 1985

  3. Residual stresses • CMC and MMC are often manufactured at high-temperatures • BEWARE: residual stresses resulting from differences in the coefficient of thermal expansion

  4. Ceramic matrix composites (CMC) • subscripts: f, p, w • eg SiCf, SiCp, SiCw • fibre, particle, whisker • reinforcement toughens matrix • minimal or negative effect on modulus • applications in • radomes • armour • cutting tools • biomedical

  5. Ceramic matrix composites (CMC) • four principal groups • complex glass forming oxides • reinforcement by micro-crystalline phases, e.g. Pyrex • engineering ceramics • SiC, Si3N4, SiMON (esp. SiAlON), Al2O3, ZrO2 • cement and concrete • (prestressed) reinforced concrete • pultrusions instead of rebars • fibre-reinforced cements • carbon/carbon composites

  6. Ceramic matrix composites (CMC) • Carbon-carbon composites • applications in • aircraft and F1 braking • rocket motor nozzle throats and exit cones • nosetips/leading edges • thermal protection systems

  7. Carbon-carbon composites • carbon fibre preform • impregnate with organic liquid then pyrolysis • phenolic or furfuryl resins • yield ~55% carbon at 1000°C • liquid pitch and high isostatic pressure (70 MPa) • yield ~85% carbon • chemical vapour deposition (CVD) • hydrocarbon precursor gas • isothermal, thermal gradient ordifferential pressure conditions

  8. Metal matrix composites (MMC) • three principal (alloy) matrix systems • aluminium • magnesium • titanium • mostly particulate reinforcement • boron-fibre/aluminium used in aerospace • little advantage to stiffness and strength • gains in creep performance, toughness,wear resistance, reduced thermal distortion

  9. Metal matrix composites (MMC) • generally high-temperature processes • interdiffusion of matrix/reinforcementproduces a (gradient) interphase • beware galvanic corrosion • C fibres in Al/Mg matrix • opposite ends of electrochemical series

  10. MMC Liquid State processes I • Liquid pressure forming (LPF)including the Cray process • similar to RTM with molten metalfed into an evacuated fibre-filled mouldfrom below by pressure. • gases and volatiles vented from mould top. • high pressures • 10-15 atm for Saffil preforms • 70 atm for 50 v/o carbon fibre • high clamping loads, • massive dies for heat retention • long solidification times.

  11. MMC Liquid State processes II • Pressure infiltration casting (PIC), including PCAST process • as LPF, but mould is a cold thin walled vessel located inside and clamped by pressure vessel • low cost tooling. • Squeeze casting: high-quality casting • pressurise to 1000-2000 atm during solidification • collapses porosity and • increases thermal contact with unheated die wall resulting in rapid solidification rate. • high capital facility and tooling costs.

  12. MMC Liquid State processes III • Casting/semi-slurry technique • two phase process for (continuous) casting • limited to short-fibre/particulate reinforcement • Phase 1: dispersal of reinforcement in melt • Phase 2: shear dilution • produces ingots for subsequent reprocessing

  13. MMC Liquid State processes IV • Osprey technique • liquid Al alloy atomised in N2 atmosphere • fed with 5μm (silicon carbide) particles • sprayed onto collector surface.

  14. MMC Solid State processes I • Low temperature processes with diffusion bonding. • Foil techniquesCompaction of fibre with foil matrixbelow the solidus temperature: • foil plating by cold rolling • explosion welding • hot pressing (HP) • hot isostatic pressing (HIP)

  15. MMC Solid State processes II • Powder techniquesAluminium alloy matrix materialscanned and vacuum-degassedprior to consolidation to minimise surface oxidation and contamination

  16. MMC secondary processing • extrusion, forging, rolling, stamping • superplastic forming • machining • superhard cutting and grinding tools • AJM:  abrasive waterjet cutting • CHM:  chemical milling • EBM:  electron beam machining • EDM:  electro-discharge machining • LBM:  laser beam machining • PAM:  plasma arc machining • USM:  ultrasonic machining

  17. Natural composites • Cellulose • most abundant polysaccharide • notably plant materials • Chitin/chitosan • second most abundant polysaccharide • found in: • crab and shrimp shells (the main commercial source) • various marine organisms, insect cuticle • fungi and yeast cells • Proteins • silk fibres

  18. Natural composites • wood • timber .. plywood .. MDF .. chipboard • reinforcements • bast (plant stem) fibres: flax, hemp, jute • leaf fibres: pineapple or sisal • seed fibres: coir or cotton • bio-based resin systems • biomimetics

  19. Nacre (abalone/mother-of-pearl) • CaCO3 aragonite crystalshexagonal platelets: 10-20 µm x 0.5 µm thick arranged in a continuous parallel lamina. • layers separated by sheets of organic matrixcomposed of elastic biopolymers (such as chitin, lustrin and silk-like proteins). • brittle platelets and thin elastic biopolymers makes the material strong and resilientdue to adhesion by the "brickwork“ arrangement of the platelets which inhibits transverse crack propagation.

  20. Nacre • Micrograph from Tomsia et al http://www.physorg.com/news10408.html • Schematic from http://en.wikipedia.org/wiki/Mother_of_pearl

  21. Natural composites • Arthur MacGregor book:“Bone, antler, ivory, horn: the technology of skeletal materials since the Roman Period” Barnes and Noble, London, 1985. • the definitive work on boneworkfrom Roman to medieval times.

  22. Polymer matrix composites (PMC) • Thermosets • AFRP, CFRP, GFRP • Thermoplastics • AFRTP, CFRTP, GFRTP • sailcloths, tarpaulins, tensile structures (eg Frei Otto) • Elastomers • cord-reinforced rubber • cotton, rayon, nylon, steel, aramid fibres • tyres, hoses, conveyor belts

More Related