1 / 24

A-dec 511 Dental Chair

A-dec 511 Dental Chair. Product Overview – Pg 10. A-dec 511 Chair Features Headrest Armrest Baseplate Back Seat Hydraulic Motor Pump Assembly. Chair Specifications – Pg 11. Load Capacity Patient 300 lb (135 kg) Accessory 250 lb (113 kg) Note: Bolt chair to floor Power On/Off Button

clare-britt
Download Presentation

A-dec 511 Dental Chair

An Image/Link below is provided (as is) to download presentation Download Policy: Content on the Website is provided to you AS IS for your information and personal use and may not be sold / licensed / shared on other websites without getting consent from its author. Content is provided to you AS IS for your information and personal use only. Download presentation by click this link. While downloading, if for some reason you are not able to download a presentation, the publisher may have deleted the file from their server. During download, if you can't get a presentation, the file might be deleted by the publisher.

E N D

Presentation Transcript


  1. A-dec 511 Dental Chair

  2. Product Overview – Pg 10 • A-dec 511 Chair • Features • Headrest • Armrest • Baseplate • Back • Seat • Hydraulic Motor Pump Assembly

  3. Chair Specifications – Pg 11 • Load Capacity • Patient 300 lb (135 kg) • Accessory 250 lb (113 kg) • Note: Bolt chair to floor • Power On/Off Button • Limp-Along Feature

  4. Chair Specifications – Pg 12 • Chair Power Supply • Comes standard with the 511 chair • Electric switch connects the power supply to pilot air

  5. Chair Flow Diagram – Pg 15

  6. Service/Usage Information – Pg 16 • Chair Covers • Motor pump cover requires hex wrench • Lift arm cover: pull outward to flex cover over stops • Stop plate cover: pull tabs out over pegs

  7. Service/Usage Information – Pg 17 • Factory Default Routine • Sets the base and back upper limits • Calculates new presets base on actual range of the chair • Verifies that the potentiometers work

  8. Chair Circuit Board – Pg 18-19 • Circuit Board Components • Refer to the table on page 18 and Figure 6 on page 19

  9. Chair Circuit Board Revisions • Rev D • Adds bump up when chair lockout detected • Increased electrical current for lift and support arm limit switches, released 01/05 • Rev E • Base up/down travel limits can be set, released 04/05 • Rev F • Positioning improved when using button for x-ray/rinse, released 06/05

  10. Circuit Board Components – Pg 20 • LED Identification

  11. Hydraulic System – Pg 21 • How the Hydraulic System Operates • Motor-driven hydraulic pump with solenoids • Hydraulic cylinders • Hydraulic Fluid Reservoir • Check with base and back full up • Use only A-dec fluid 61.0197.00 • System holds 40 ounces • 1.18 liters.

  12. Hydraulic System • Bidirectional motor • Replace as compete assembly • Depressurize the system before disassembling hydraulic components.

  13. Hydraulic System – Pg 22 • Hydraulic Cylinders • The hydraulic cylinders operate during Base Up and Back Up functions. Springs and gravity retract the piston during Base Down and Back Down functions. • The chair seat travels vertically from a low point of 13.5” (343mm) to a high point of 31.5” (800mm) above the floor.

  14. Chair Hydraulic Base Cylinder • Base cylinder replacement • Remove motor pump, lift arm and stop plate covers • Position chair base up • Lower chair on solid support • Remove rod screw and the pivot pin • Remove reservoir cap • Operate base down while pushing rod into cylinder • Remove 2 screws at base of cylinder • Remove hydraulic hose from cylinder

  15. Chair Hydraulic Back Cylinder • Back cylinder replacement • Remove seat and back upholstery • Position chair back down • Remove hydraulic hose and vent line from cylinder • Remove snap ring at rear of trunion • Unscrew cylinder rod from bearing clevis using a 9/64 hex key through hole • Pull cylinder out from front of trunion

  16. Hydraulic System – Pg 23 • Capacitor • The capacitor is energized during chair Base Up or Back Up functions. • Voltage and mF specific

  17. Hydraulic System – Pg 24 • Solenoids • Down only • Line voltage specific • How to Test Solenoids • To check for a failed solenoid, test the solenoids using a volt/ohm meter or magnetic pull test.

  18. Hydraulic System • Pump Motor Assembly • Soft Start/Stop • Accumulator - dampens hydraulic shockby acting like a shock absorber. • Bi-directional Pump • Turns one direction for Base Up,the opposite for Back Up • Gravity and springs only forBase Down and Back Down Accumulator

  19. Potentiometer – Pg 25 • Back and base pots are interchangeable assemblies • P/N 90.1069.00

  20. Chair Stop Plate – Pg 26 • Activation causes chair to stop down movement, PCB signals momentary base up

  21. Swivel Brake – Pg 27 • Swivel Brake Adjustment • Release brake tension • Insert 7/64” hex wrench in through-hole and into adjustment screw • Turn wrench to right to increase brake friction

  22. Headrest – Pg 28 • Drift Adjustment • Use 1/8” hex wrench • Turn clockwise to increase friction on glide bar

  23. IPB – Pgs 29-47 • Part Identification • Baseplate & Motor Pump Assembly • Hydraulic Hose & Solenoid Assembly • Lift Cylinder & Link Arm • Lower Assembly • Upper Structure/Swivel Assembly • Upper (Seat Assembly) • Headrest Assembly

  24. A-dec 511 Dental Chair

More Related