1 / 14

Lesson 9: Solid Rocket Propulsion Basics

Lesson 9: Solid Rocket Propulsion Basics. Dr. Andrew Ketsdever. Solid Rocket Motors. A solid rocket motor is a system that uses solid propellants to produce thrust Advantages High thrust Simple Storability High density Isp Disadvantages Low Isp (compared to liquids)

chaim
Download Presentation

Lesson 9: Solid Rocket Propulsion Basics

An Image/Link below is provided (as is) to download presentation Download Policy: Content on the Website is provided to you AS IS for your information and personal use and may not be sold / licensed / shared on other websites without getting consent from its author. Content is provided to you AS IS for your information and personal use only. Download presentation by click this link. While downloading, if for some reason you are not able to download a presentation, the publisher may have deleted the file from their server. During download, if you can't get a presentation, the file might be deleted by the publisher.

E N D

Presentation Transcript


  1. Lesson 9: Solid Rocket Propulsion Basics Dr. Andrew Ketsdever

  2. Solid Rocket Motors • A solid rocket motor is a system that uses solid propellants to produce thrust • Advantages • High thrust • Simple • Storability • High density Isp • Disadvantages • Low Isp (compared to liquids) • Complex throttling • Difficult to stop and restart • Safety

  3. Solid Rocket Motors • Solid rocket motors are used for • Launch vehicles • High thrust (high F/W ratio) • High storage density • Ballistic Missiles • Propellant storability • Excellent aging • Quick response • storability • high F/W ratio)

  4. Solid Rocket Motor Components

  5. Thermal Insulation • Design involves: • Analysis of combustion chamber environment • Stagnation temperature • Stagnation pressure • Propellant gases (material compatibility) • Selection of insulation material • Material thickness determination for various areas of the motor case • For the cylindrical part of the case, the walls are only exposed to hot combustion gases at the end of the burn

  6. The Nozzle • The design of the nozzle follows similar steps as for other thermodynamic rockets • Throat area determined by desired stagnation pressure and thrust level • Expansion ratio determined by ambient pressure or pressure range to allow maximum efficiency • Major difference for solid propellant nozzles is the technique used for cooling • Ablation • Fiber reinforced material used in and near the nozzle throat (carbon, graphite, silica, phenolic)

  7. Ablation • Meteorite • Re-entry speed of 10 - 20 km/sec • Extreme heating in the atmosphere • Ablation and internal energy modes cooled the meteorite through its fall • Ablation gas cloud • Dissociation • Internal energy deposition • Stony-Iron Classification • (95% of all meteorites)

  8. Ignition System • Large solid motors typically use a three-stage ignition system • Initiator: Pyrotechnic element that converts electrical impulse into a chemical reaction (primer) • Booster charge • Main charge: A charge (usually a small solid motor) that ignites the propellant grain. Burns for tenths of a second with a mass flow about 1/10 of the initial propellant grain mass flow.

  9. Propellant Grain • Two main catagories • Double Base: A homogeneous propellant grain, usually nitrocellulose dissolved in nitroglycerin. Both ingredients are explosive and act as a combined fuel, oxidizer and binder • Composite: A heterogeneous propellant grain with oxidizer crystals and powdered fuel held together in a matrix of synthetic rubber binder. • Less hazardous to manufacture and handle

  10. Conventional Composite • Fuel • 5-22% Powdered Aluminum • Oxidizer • 65-70% Ammonium Perchlorate (NH4ClO4 or AP) • Binder • 8-14% Hydroxyl- Terminated Polybutadiene (HTPB)

  11. Fuels • Aluminum (Al) • Molecular Weight: 26.98 kg/kmol • Density: 2700 kg/m3 • Most commonly used • Magnesium (Mg) • Molecular Weight: 24.32 kg/kmol • Density: 1750 kg/m3 • Clean burning (green) • Beryllium (Be) • Molecular Weight: 9.01 kg/kmol • Density: 2300 kg/m3 • Most energetic, but extremely toxic exhaust products

  12. Oxidizers • Ammonium Perchlorate (AP) • Most commonly used • Cl combining with H can form HCl • Toxic • Depletion of ozone • Ammonium Nitrate (AN) • Next most commonly used • Less expensive than AP • Less energetic • No hazardous exhaust products

  13. Binders • Hydroxyl Terminated Polybutadiene (HTPB) • Most commonly used • Consistency of tire rubber • Polybutadiene Acrylonitrile (PBAN) • Nitrocellulose (PNC) • Double base agent

  14. Additives • Used to promote • Curing • Enhanced burn rate (HMX) • Bonding • Reduced radiation through the grain (darkening) • Satisfactory aging • Reduced cracking

More Related