1 / 25

Induction Motor Review By Mr.M.Kaliamoorthy Department of Electrical & Electronics Engineering PSNA College of Engin

Induction Motor Review By Mr.M.Kaliamoorthy Department of Electrical & Electronics Engineering PSNA College of Engineering and Technology. Outline. Introduction Construction Concept Per-Phase Equivalent Circuit Power Flow Torque Equation T-  Characteristics Starting and Braking

catalina
Download Presentation

Induction Motor Review By Mr.M.Kaliamoorthy Department of Electrical & Electronics Engineering PSNA College of Engin

An Image/Link below is provided (as is) to download presentation Download Policy: Content on the Website is provided to you AS IS for your information and personal use and may not be sold / licensed / shared on other websites without getting consent from its author. Content is provided to you AS IS for your information and personal use only. Download presentation by click this link. While downloading, if for some reason you are not able to download a presentation, the publisher may have deleted the file from their server. During download, if you can't get a presentation, the file might be deleted by the publisher.

E N D

Presentation Transcript


  1. Induction Motor Review By Mr.M.Kaliamoorthy Department of Electrical & Electronics Engineering PSNA College of Engineering and Technology

  2. Outline • Introduction • Construction • Concept • Per-Phase Equivalent Circuit • Power Flow • Torque Equation • T- Characteristics • Starting and Braking • References

  3. Introduction • Induction motors (IM) most widely used • IM (particularly squirrel-cage type) compared to DC motors • Rugged • Lower maintenance • More reliable • Lower cost, weight, volume • Higher efficiency • Able to operate in dirty and explosive environments

  4. Introduction • IM mainly used in applications requiring constant speed • Conventional speed control of IM expensive or highly inefficient • IM drives replacing DC drives in a number of variable speed applications due to • Improvement in power devices capabilities • Reduction in cost of power devices

  5. 120o 120o 120o Induction Motor – Construction • Stator • balanced 3-phase winding • distributed winding – coils distributed in several slots • produces a rotating magnetic field • Rotor • usually squirrel cage • conductors shorted by end rings • Rotating magnetic field induces voltages in the rotor • Induced rotor voltages have same number of phases and poles as in stator winding a c’ b’ c b a’

  6. Induction Motor – Construction

  7. Induction Motor – Concept • Stator supplied by balanced 3-phase AC source (frequency f Hz or  rads/sec ) • field produced rotates at synchronous speed s rad/sec (1) where P = number of poles • Rotor rotates at speed m rad/sec (electrical speed r= (P/2) m) • Slip speed, sl – relative speed (2) between rotating field and rotor • Slip, s – ratio between slip speed and synchronous speed (3)

  8. Induction Motor – Concept • Relative speed between stator rotating field and rotor induces: • emf in stator winding (known as back emf), E1 • emf in rotor winding, Er • Frequency of rotor voltages and currents: (4) • Torque produced due to interaction between induced rotor currents and stator field • Stator voltage equation: • Rotor voltage equation:

  9. Induction Motor – Concept • E1 and Er related by turns ratio aeff • Rotor parameters can be referred to the stator side : Ir Lls Llr Is Rs + Vs – + E1 – + Er – Rr/s Lm Im

  10. Lls Is Llr’ Ir’ Rs + E1 – + Vs – Rr’/s Lm Im Induction Motor – Per Phase Equivalent Circuit • Rs – stator winding resistance • Rr’ – referred rotor winding resistance • Lls – stator leakage inductance • Llr’ – referred rotor leakage inductance • Lm – mutual inductance • Ir’ – referred rotor current

  11. Induction Motor – Power Flow ConvertedPowerPconv Airgap Power Pag Mechanical Power Electrical Power Rotational losses Prot (Friction and windage, core and stray losses) Rotor Copper Loss (RCL) Note: Stator Copper Loss (SCL)

  12. Induction Motor – Torque Equation • Motor induced torque is related to converted power by: (5) • Since and , hence (6) • Substituting for Ir’ from the equivalent circuit: (7)

  13. Induction Motor – T- Characteristic • T- characteristic of IM during generating, motoring and braking

  14. Induction Motor – T- Characteristic Te • Maximum torque or pullout torque occurs when slip is: (8) • The pullout torque can be calculated using: (9) Pull out Torque (Tmax) Trated r 0 rated smax s s 1 0

  15. Induction Motor – T- Characteristic Te Linear region of operation (small s) • Te s • High efficiency • Pout = Pconv – Prot • Pconv = (1- s )Pag • Stable motor operation Pull out Torque (Tmax) Trated 0 rated smax r s s 1 0

  16. Induction Motor – NEMA Classification of IM • NEMA = National Electrical Manufacturers Association • Classification based on T- characteristics • Class A & B – general purpose • Class C – higher Tstart(eg: driving compressor pumps) • Class D – provide high Tstartand wide stable speed range but low efficiency s

  17. Induction Motor – Starting • Small motors can be started ‘direct-on-line’ • Large motors require assisted starting • Starting arrangement chosen based on: • Load requirements • Nature of supply (weak or stiff) • Some features of starting mechanism: • Motor Tstartmust overcome friction, load torque and inertia of motor-load system within a prescribed time limit • Istart magnitude ( 5-7 times I rated) must not cause • machine overheating • Dip in source voltage beyond permissible value

  18. Induction Motor – Starting • Methods for starting: • Stat-delta starter • Autotransformer starter • Reactor starter • Soft Start

  19. Induction Motor – Starting • Star-delta starter • Special switch used • Starting: connect as ‘star’ (Y) • Stator voltages and currents reduced by 1/√3 • Te VT2  Te reduced by 1/3 • When reach steady state speed • Operate with ‘delta’ ( ) connection • Switch controlled manually or automatically

  20. Induction Motor – Starting • Autotransformer starter • Controlled using time relays • Autotransformer turns ratio aT • Stator voltages and currents reduced by aT • Te VT2  Te reduced by aT2 • Starting: contacts 1 & 2 closed • After preset time (full speed reached): • Contact 2 opened • Contact 3 closed • Then open contact 1

  21. Induction Motor – Starting • Reactor starter • Series impedance (reactor) added between power line and motor • Limits starting current • When full speed reached, reactors shorted out in stages

  22. Induction Motor – Starting • Soft Start • For applications which require stepless control of Tstart • Semiconductor power switches (e.g. thyristor voltage controller scheme) employed • Part of voltage waveform applied • Distorted voltage and current waveforms (creates harmonics) • When full speed reached, motor connected directly to line

  23. Induction Motor – Braking • Regenerative Braking: • Motor supplies power back to line • Provided enough loads connected to line to absorb power • Normal IM equations can be used, except s is negative • Only possible for  > s when fed from fixed frequency source • Plugging: • Occurs when phase sequence of supply voltage reversed • by interchanging any two supply leads • Magnetic field rotation reverses  s > 1 • Developed torque tries to rotate motor in opposite direction • If only stopping is required, disconnect motor from line when  = 0 • Can cause thermal damage to motor (large power dissipation in rotor)

  24. Induction Motor – Braking • Dynamic Braking: • Step-down transformer and rectifier provides dc supply • Normal: contacts 1 closed, 2 & 3 opened • During braking: Contacts 1 opened, contacts 2 & 3 closed • Two motor phases connected to dc supply - produces stationary field • Rotor voltages induced • Energy dissipated in rotor resistance – dynamic braking

  25. References • Chapman, S. J., Electric Machinery Fundamentals, McGraw Hill, New York, 2005. • Rashid, M.H, Power Electronics: Circuit, Devices and Applictions, 3rd ed., Pearson, New-Jersey, 2004. • Trzynadlowski, Andrzej M. , Control of Induction Motors, Academic Press, 2001. • Nik Idris, N. R., Short Course Notes on Electrical Drives, UNITEN/UTM, 2008. • Ahmad Azli, N., Short Course Notes on Electrical Drives, UNITEN/UTM, 2008.

More Related