1 / 13

Background JET / ITER

Planned physics experiments with ILA J. Ongena, acting TFH Leader ERM-KMS, Association EURATOM-Belgian State, Brussels. Background JET / ITER. ITER requirements for ICRF is to couple 20 MW on plasma with two major issues : ELMy H-mode Antenna - plasma separatrix ~ 14 cm

brygid
Download Presentation

Background JET / ITER

An Image/Link below is provided (as is) to download presentation Download Policy: Content on the Website is provided to you AS IS for your information and personal use and may not be sold / licensed / shared on other websites without getting consent from its author. Content is provided to you AS IS for your information and personal use only. Download presentation by click this link. While downloading, if for some reason you are not able to download a presentation, the publisher may have deleted the file from their server. During download, if you can't get a presentation, the file might be deleted by the publisher.

E N D

Presentation Transcript


  1. Planned physics experiments with ILA J. Ongena, acting TFH LeaderERM-KMS, Association EURATOM-Belgian State, Brussels

  2. BackgroundJET / ITER • ITER requirements for ICRF is to couple 20 MW on plasma with two major issues : • ELMy H-mode • Antenna - plasma separatrix ~ 14 cm • Faraday shield recessed ~ 1cm + Faraday shield - strap ~ 5 cm =>Antenna strap - separatrix ~ 20 cm • JET ideal to study coupling in such conditions: • ICRF system with fast data acquisition • The ELMy H modes • Can operate with ROG  14 cm • Antenna strap - separatrix ~ 19 cm

  3. LH and ICRH Systems in JET LH Launcher JET-EP Antenna ICRH Antenna A ICRH Antenna B

  4. BackgroundAntenna loading in general (in L-mode conditions) • In L-mode, R variation well documented (lA ~ assumed constant) • Main dependence is exponential decrease with ROG ( antenna- cut-off density) • Example: • ROG < 4 cm => R > 3 Ohm = “good” coupling • 4 cm < ROG < 7 cm => 1.5 Ohm < R < 3 Ohm = coupling OK • 7 cm < ROG < 10 cm => R< 1 Ohm - Bad coupling Almost no data at ROG > 10 cm but very very bad coupling expected !

  5. JET’s gas injection system GIM : Gas Inlet Module GIM10 GIM12 GIM9 GIM11

  6. GIM12 GIM10 GIM9 GIM11 Antenna position in JET • Main diagnostics : • RCP, Lithium beam, edge LIDAR, fast interferometer data • Visible spectro. DD/S3-AD34 = Oct.1 vertical view  below midplane LFS • Magnetic connection of antennas to edge diagnostics : RCP, Li-beam • D2 gas injection: • From divertor GIMs 9 + 10 as in ref. • Add  level injection from GIM6 ILA

  7. Optimization of gas puff needed • ROG fixed at 14 cm • During D2 injection from GIM 6 • Improvement on ALL the antennas • During D2 injection from GIM 10 • No obvious improvement • gas injected from divertor • Fuelling less efficient ! • Also need to check effect on density, confinement, ELMs. Rc(A1) (Ohm) Rc(B1) (Ohm) Rc(C1) (Ohm) Rc(D1) (Ohm) 1022 el/s GIM6 GIM10 Da V

  8. Effect of gas injection / ROGBetween ELMS • Coupling for ROG ~14 cm very poor << 1 Ohm • D2 injection : • from divertor: • R X by 1.5 to 3 • from the midplane: • R X 2.5 to 6 ! • R up to 2 Ohm ! Good coupling ! Increasing ROG Increasing gas GIM6 @ 8 1021el/s GIM6 @ 4 1021el/s GIM 10,9 No GIM6 No gas

  9. GIM12 GIM10 GIM9 GIM11 High power ICRH at large plasma-strap distance with gas puff Coupling studies in ITER-relevant plasma configuration (dl~0.50, du~0.38) #68752, 1.9MA /3.0T 8MW power coupled ELMs present Using gas from various positions Distance antenna box-separatrix 14cm Clear effect on Te (+1 keV) and Wdia (+1 MJ)

  10. Effect of ICRH on LH coupling 3.4T/2.4MA, 51MHz, dipole phasing no gas from GIM6 • Depends on power and phasing from ICRH antennas magnetically connected to LH grill • Worse at higher power, and at -90 and monopole phasing. Effect not homogeneous poloidally • Puffing D2 near the LH launcher to increase ne,SOL alleviates problem in most cases • Also for operation with ILA in JET: will be magnetically connected

  11. Assess sheat effects • Antennae A and B viewed by the wide angle IR camera. • Specific session in 2007 dedicated to the characterisation of heating with RF • Important temperature increase with RF on upper part of septa SA SB 70439, t=59 s. PICRFA=PICRFB=2 MW

  12. A2 antennae septum temperature on JET Temperature evolution of septum A, septum B and limiter 1, pulse 70438, with power on antenna A, B and D, and NBI power. ROG= 3 cm.

  13. Physics experiments planned with ILA Questions to this group : • Details needed of currently assumed ITER scenarios : • n/nG, H98, heating scenarios, ELM size, assumed edge conditions,…. ? • What is optimal ROG in JET to mimic ITER assumed edge density conditions ? • What is optimal size of ELMs to use in JET ? • ….

More Related