1 / 39

Katrin Dahl for the AEI 10 m Prototype team

AEI 10m Prototype. S uspension P latform I nterferometer for the AEI 10 m Prototype Interferometer Introductory talk. Katrin Dahl for the AEI 10 m Prototype team. September 2009 –AEI seminar. Outline. AEI 10 m Prototype Interferometer > Why is an SPI needed?

borka
Download Presentation

Katrin Dahl for the AEI 10 m Prototype team

An Image/Link below is provided (as is) to download presentation Download Policy: Content on the Website is provided to you AS IS for your information and personal use and may not be sold / licensed / shared on other websites without getting consent from its author. Content is provided to you AS IS for your information and personal use only. Download presentation by click this link. While downloading, if for some reason you are not able to download a presentation, the publisher may have deleted the file from their server. During download, if you can't get a presentation, the file might be deleted by the publisher.

E N D

Presentation Transcript


  1. AEI 10m Prototype Suspension Platform Interferometer for the AEI 10m Prototype Interferometer Introductory talk Katrin Dahl for the AEI 10m Prototype team September 2009 –AEI seminar

  2. Outline • AEI 10m Prototype Interferometer • > Why is an SPI needed? • Relative distance measurement experiments • Experimental setup design • Test setup • Future plans

  3. The AEI 10m Prototype Goals: • Train peoplefor GEO600 • Provenewtechniques (PSL, digital controlsystem, Khalili cavity…) • Provideultralowdisplacementnoisetestingenvironment • To probe at (and later go beyond) the SQL • Entanglement of macroscopic test masses • For geodesy/LISA related experiments • ...

  4. Noise spectrum

  5. Vacuum system Tank centers separatedby11.65m Volume ca. 100 m3 22 t stainless steel Tubes: 1.5 m diameter Tanks: 3 m diameter, 3.4 m tall • 10-6mbar after about 12 hours , • 10-7mbar after about 2 weeks • ofpumping • Roughing: One 170 l/s screw pump • Main pumps: Two 2000 l/s turbo-molecularpumps • Backingand differential pumping: Two scroll pumps

  6. Seismic Attenuation System One SAS per vacuum tank, optical table goes on top of SAS Improved version of HAM-SAS Resonance frequency around 0.1Hz Up to 80dB attenuation in both vertical and horizontal directions Angstrom residual motion above 1Hz

  7. Why a Suspension Platform Interferometer? • Ease lock acquisition of cavities by reducing residual test mass motion • Reduction of burden to actuators on the mirrors • Testbed for GRACE follow-on and LISA related experiments  Sets requirements on SPI

  8. Horizontal table actuation

  9. Vertical table actuation

  10. Vertical table actuation

  11. A little bit of history LIGO-T870001-00-R

  12. Suspension Point Interferometer • monitors differential motion of the suspension points of input and end test masses LIGO-T070209-00-Z

  13. Suspension Point Interferometer LIGO-T070209-00-Z

  14. Digital Interferometry Advantages: • no specific lock point • continuous sensing • track the position of • mirrors over many µm LIGO-T080139-00-I

  15. Stabilised metrology testbed around 1m K Numata, J Camp, Proc. of SPIE Vol. 6265

  16. Stabilised metrology testbed Control bandwidth 10 Hz Yaw angle motion of 20nrad/sqrt(Hz) at 10mHz leading to about 50 times worse result for only one controlled degree of freedom K Numata, J Camp, Proc. of SPIE Vol. 6265

  17. THE AEI SPI • Requirements: • No specific lock point • Control bandwidth 100 Hz • 100pm/sqrt(Hz) and 10nrad/sqrt(Hz) @ 10mHz • Heterodyne Mach-Zehnderinterferometry • Suits our needs best • In-house knowledge ....Thanks LTP/LISA folks!

  18. Heterodyne Mach-Zehnder IFO

  19. Optical layout

  20. Measurement bench • Beam height 45mm • Overall height below 65mm

  21. Phase determination Phase isextractedfromheterodynesignalbyuse of an hardwarePhasemeterbased on FPGA chips • Preamplifierand A/D conversion • Photocurrentconvertedtovoltage • Digitisingsignals •  results in time series • Single bin discrete Fourier transform • Fourier transformatonlyonefrequency •  complexamplitudeof PD signalatfhet • Signal combinationofeach QPD quadrantleadstophase, DC, Differential WavefrontSensing (DWS) andcontrastinformation Illustration of DWS

  22. Choice of parameters • Due to the arm length mismatch (20m optical path length) a highly stabilised laser is necessary: • 280Hz/sqrt(Hz) @ 10mHz for green light (532nm) or • 140Hz/sqrt(Hz) @ 10mHz for IR light (1064nm) •  decision made for 1064nm

  23. Iodine stabilised Nd:YAG laser output power: 1W Stabilisation via Modulation Transfer Spectroscopy Michael Tröbs

  24. Choice of parameters • According to the arm length mismatch (20m optical path length) a highly stabilised laser is necessary: • 280Hz/sqrt(Hz) @ 10mHz for green light (532nm) or • 140Hz/sqrt(Hz) @ 10mHz for IR light (1064nm) •  decision made for 1064nm • Control bandwidth 100Hz  heterodyne frequency around 20kHz  new phasemeter interface needed

  25. Phasemeter Interface

  26. Choice of parameters • According to the arm length mismatch (20m optical path length) a highly stabilised laser is necessary: • 280Hz/sqrt(Hz) @ 10mHz for green light (532nm) or • 140Hz/sqrt(Hz) @ 10mHz for IR light (1064nm) •  decision made for 1064nm • Control bandwidth 100Hz  heterodyne frequency around 20kHz • Thermal driftsrequirescomponentstobemonolithicallybondedtoplatewithlow CTE (ClearCeram, CTE=0.4*10-7/K)

  27. UV curing epoxy • Advantage: almost infinite alignment time • Optocast 3553-LV-UTF • CTE = 55PPM/°C, viscosity @ 25°C = 500cps • cps = centipoise, water = 1cps, castrol oil = 1,000cps, honey = 10,000cps, ketchup = 50,000cps • Disadvantage: layer thickness is not reproducible, e.g. 10µm, 98µm, 79µm, 70µm, 37µm  misalignment in pitch •  stick to hydroxide-catalysis bonding technique

  28. Optical layout

  29. Expected transversal signals Phase difference [rad] contrast -2 -1 0 1 2 -2 -1 0 1 2 Transveral displacement of MW1 or MS1 [mm] Transveral displacement of MW1 or MS1 [mm] DC DWS [rad] Red curve: PDCW1 Black curve: PDCS1 -2 -1 0 1 2 -2 -1 0 1 2 Transveral displacement of MW1 or MS1 [mm] Transveral displacement of MW1 or MS1 [mm]

  30. Expected longitudinal signals contrast Phase difference [rad] -2 -1 0 1 2 -2 -1 0 1 2 Longitudinal displacement of MW1 or MS1 [mm] Longitudinal displacement of MW1 or MS1 [mm] DWS [rad] DC Red curve: PDCW1 Black curve: PDCS1 -2 -1 0 1 2 -2 -1 0 1 2 Longitudinal displacement of MW1 or MS1 [mm] Longitudinal displacement of MW1 or MS1 [mm]

  31. Expected rotational signals Phase difference [rad] contrast -10 -5 0 5 10 -10 -5 0 5 10 Rotation of MW1 or MS1 [mdeg] Rotation of MW1 or MS1 [mdeg] DWS [rad] DC Red curve: PDCW1 Black curve: PDCS1 -10 -5 0 5 10 -10 -5 0 5 10 Rotation of MW1 or MS1 [mdeg] Rotation of MW1 or MS1 [mdeg]

  32. Test setup • Use of vacuum • compatible • components • (free of grease)

  33. Longitudinal displacement

  34. Pitch

  35. Yaw

  36. Blind test

  37. Blind test

  38. Next steps • Stabilisation loops • Amplitude stabilisation @ 20kHz • Optical pathlenght difference stabilisation • Bond optics • Build calibrated QPD • Use CDS via phasemeter interface • Install final setup inside vacuum envelope • Calibrate signals • Table actuation • Reach design sensitivity

  39. The End

More Related