1 / 40

Required Design Parameters

Heat Exchanger Design Thermal / Fluid System Design Final Project Department of Mechanical Engineering Fall 2005 December 13, 2005 Team Members: Andrew Burian Jack Copenhaver Chris Haire Brandin Ray Professor: John Toksoy. Required Design Parameters.

badru
Download Presentation

Required Design Parameters

An Image/Link below is provided (as is) to download presentation Download Policy: Content on the Website is provided to you AS IS for your information and personal use and may not be sold / licensed / shared on other websites without getting consent from its author. Content is provided to you AS IS for your information and personal use only. Download presentation by click this link. While downloading, if for some reason you are not able to download a presentation, the publisher may have deleted the file from their server. During download, if you can't get a presentation, the file might be deleted by the publisher.

E N D

Presentation Transcript


  1. Heat Exchanger DesignThermal / Fluid System DesignFinal ProjectDepartment of Mechanical EngineeringFall 2005December 13, 2005Team Members:Andrew BurianJack CopenhaverChris HaireBrandin RayProfessor: John Toksoy

  2. Required Design Parameters • Heat Exchanger Must Cool the Chemical From 35°C to 25°C • Cannot Exceed 7m In Length or 2m in Diameter • Minimize Heat Exchanger Shell Diameter and Tube Length to Reduce Cost • Minimize Pressure Drop • Chemical Mass Flow Rate Fixed at 80 kg/hr • City Water to be Used as Cooling Fluid With an Inlet Temperature of 20°C

  3. Assumptions • Isothermal Material Properties (Shell and Tube) • Constant Properties • Steady State • Incompressible Fluids • 24 Hour Duty Cycle • Heat Transfer Through Shell is Minimal

  4. Mass Flow Rate (Shell Side) Tube Length Shell I.D. Tube Pitch Tube Material Shell Thickness Tube O.D. Tube Thickness Number of Tubes Baffle Spacing Baffle Cut Shell Material Flow Direction Initial Possible Factors Effecting Heat Exchanger Design

  5. “One Factor at a Time” Study

  6. Tube Length Shell I.D. Baffles Tube O.D. Number of Tubes Pitch (Square or Triangular) Mass Flow Rate Factors Found to Have Greatest Effect on Weight and Heat Transfer

  7. Main Effects Plots With Seven Factors

  8. Final Factors • Tube Length • Tube Material • Tube O.D. • Shell I.D.

  9. Main Effects Plots With Final Factors

  10. Final Design Specifications(Clean Heat Exchanger) • Shell I.D. =.3048m • Shell Thick. = 2mm • Tube O.D. = 9.25mm • Tube Thick. = .559mm • Number of Tubes = 550 • Weight = 590.80kg

  11. Initial vs. Final Specifications InitialFinal Mass Flow Rate ……….. 59.0 kg/s 43.0 kg/s Flow Direction …………. Counter Flow Counter Flow Shell I.D. ……………….. 0.3784 m 0.3048 m Shell Thickness ……….. 2.0 mm 2.0 mm Shell Material ………….. Bronze Stainless Steel Tube O.D. ……………… 9.525 mm 9.525 mm Tube Thickness ……….. 0.889 mm 0.559 mm Tube Length …………… 3.2 m 4 m Number of Tubes……… 889 550 Tube Material…………... Aluminum Stainless Steel Tube Pitch………………. Triangle (30°) Triangle (60°) Baffle space…………….. 0.75 m 2 m Baffle Cut……………….. 0.116 m 0.150 m

  12. The Argument for Stainless Steel

  13. Not Chemically Reactive Easy to Clean Not as Easily Damaged During Cleaning Food Industry Uses Easy to Repair Harder to Machine Shipping Costs/Requirements Small Decrease in Heat Transfer Stainless SteelProsCons

  14. Easy to Work With Light Weight Slightly Increased Heat Transfer Soft – Easier to Damage During Maintenance Hard to Repair Anodic to Most Other Metals Chemically Reactive Weak (With Respect to Stainless) AluminumProsCons

  15. Stress Analysis Using General Material Properties for Annealed 300 Series Stainless Steel and “Worse Case” Heat Exchanger Pressures Taken From D.O.E. Study

  16. Shell I.D. = 0.3048 m Shell Thick. = 2 mm Tube O.D. = 9.25 mm Tube Thick. = 0.559 mm ∆ PShell = 3000 Pa ∆PTube = 14000 Pa E = 190 GPa α = 17.2 e – 6 σY = 6.55 GPa H. E. Specifications and Properties

  17. Calculated StressesσY = 6.55 GPa • Shell Hoop Stress = 2.29 GPa • Shell Long. Stress = 1.14 GPa • Tube Hoop Stress = 1.02 GPa • Tube Thermal Stress = 19.7 KPa

  18. Questions?

  19. Appendix

  20. Desired Heat Transfer Rate = 928500.92 W Calculated Heat Transfer Rate = 929320.42 W Difference = -819.50 W Desired-to-Calculated Ratio = 1.00 HE Pressure Drop ===================== Shell Side Delta-P = 2181.04 Pa Tube Side Delta-P = 5363.92 Pa Heat Exchanger Weight ===================== Shell Weight = 60.72 kg Tube Weight = 273.66 kg Shell Fluid Weight = 134.82 kg Tube Fluid Weight = 121.61 kg ----------- Total HE Weight = 590.80 kg Tube Side Heat Transfer Parameters ======================================== Number of Tubes N = 550.00 Number of Passes = 1.00 Tubes OD OD = 0.0095 m Tubes ID ID = 0.0084 m Tube Length L = 4.0000 m Tube Flow Area Af = 0.0305 m2 Tube Solid Area As = 0.0392 m2 Tube Pitch PT = 0.0119 m Average Velocity V = 0.73 m/s Mass Velocity G = 727.87 kg/m2.s Reynolds Number Re = 7657.84 TURBULENT Nusselt Number Nu = 63.05 HT Coefficient h = 4629.32 W/m2.C MATLAB Results With Optimized Factors

  21. Overall Heat Transfer Coefficient ====================================== U (Tube Outside Area) = 1975.17 W/m2.C Heat Transfer Rate ====================================== Desired Heat Transfer Rate = 928500.92 W Calculated Heat Transfer Rate = 929320.42 W Difference = -819.50 W Desired-to-Calculated Ratio = 1.00 Shell Side Heat Transfer Parameters ====================================== Shell ID = 0.3048 m Shell Cross Sec Area = 0.0730 m2 Shell Flow Area = 0.1219 m2 Baffle Space = 2.0000 m Number of Baffles = 1.0000 m Shell Equivalent Dia = 0.0069 m Mass Velocity G = 352.69 kg/m2.s Reynolds Number Re = 2576.25 TURBULENT Nusselt Number Nu = 51.07 HT Coefficient h = 4502.58 W/m2.C

  22. Additional Plots From Seven Factors MINITAB Run

  23. Pareto Charts With All Combinations Considered

  24. Pareto Charts With Irrelevant Combinations Removed

  25. Credits • Minitab 14 • MatLab 7.0

More Related