1 / 16

GEOCHEMICAL METHODS FOR THE DETERMINATION OF DIFFERENT METAL SPECIES (cont’d)

GEOCHEMICAL METHODS FOR THE DETERMINATION OF DIFFERENT METAL SPECIES (cont’d). PART -III Analytical Methods for Metal Speciation in Water and Solids. COMMONLY USED ANALYTICAL SPECIATION TECHNIQUES FOR METALS IN ENVIRONMENTAL SAMPLES. Liquid Samples * Alkylation techniques

auyeung
Download Presentation

GEOCHEMICAL METHODS FOR THE DETERMINATION OF DIFFERENT METAL SPECIES (cont’d)

An Image/Link below is provided (as is) to download presentation Download Policy: Content on the Website is provided to you AS IS for your information and personal use and may not be sold / licensed / shared on other websites without getting consent from its author. Content is provided to you AS IS for your information and personal use only. Download presentation by click this link. While downloading, if for some reason you are not able to download a presentation, the publisher may have deleted the file from their server. During download, if you can't get a presentation, the file might be deleted by the publisher.

E N D

Presentation Transcript


  1. GEOCHEMICAL METHODS FOR THE DETERMINATION OF DIFFERENT METAL SPECIES (cont’d) PART -III Analytical Methods for Metal Speciation in Water and Solids

  2. COMMONLY USED ANALYTICAL SPECIATION TECHNIQUES FOR METALS IN ENVIRONMENTAL SAMPLES Liquid Samples * Alkylation techniques * Redox based techniques Solid samples * Chemical sequential extraction techniques * Qualitative physical analytical techniques (minerals)

  3. 1. ANALYTICAL APPROACHES FOR METAL SPECIATION IN LIQUID SAMPLES 1.1. Chromatography and metal speciation: (e.g. chromium +3 and +6, inorganic and organic arsenic compounds, organo-metal species (e.g. methyl-mercury)…) 1.2. Redox chemistry combined with: * hydride generation and spectrocopy (e.g. arsenic +3 and +5) * Purge and trap and detection by spectrometry

  4. 2. SOLID SAMPLES IN AQUATIC SYSTEMS: SUSPENDED SOLIDS AND SEDIMENTS 2.1. MAIN COMPONENTS: 2.1.1. SAND: weathered grain of SiO2 (quartz). Large particle size – small specific surface area – low to no binding capacity for metals 2.1.2. SILT: Medium size particles – broken down minerals such as quartz, feldspar, etc. – specific surface area remains rather small with low binding capacity

  5. 2.1.3. CLAY: Comprised of layer of silicates formed from two basic units: (1). A tetrahedron of 4 oxygen atoms surrounding a central cation, primarily Si4+ (2). An octahedron of 6 oxygen atoms or hydroxyls around a large cation that is commonly Al3+

  6. Example clay mineral - 1Kaolinite: a 1:1-layer clay mineral General chemical formula: Al2Si2O5(OH)4 OH OH Alumina octahedra OH OH Silica tetrahedra OH Alumina octahedra Silica tetrahedra OH OH -OH -O- + H+

  7. Example clay mineral - 2Montmorillonite: a 2:1 - layer clay mineral This is an hydrated sodium calcium aluminium magnesium silicate hydroxide (Na,Ca)0.33(Al,Mg)2(Si4O10)(OH)2·nH2O. Montmorillonite is a 2:1 clay = 2 tetrahedral sheets sandwiching a central octahedral sheet

  8. 2.1.4. ORGANIC MATTER Model Humic Acid Dimethylsulfoniopropionate

  9. 2.2. APPROACH FOR METAL SPECIATION IN PARTICULATE MATTER • 2.2.1. Identification of the different metal fractions • Easily exchangeable fraction • Fraction bound to carbonate minerals • Fraction bound Fe- and Mn-oxide minerals • Fraction bound to organic matter • Refractory/Residual fraction • 2.2.2. Development of extraction/solubilization methods • Choice of chemical agents to specifically target one of the above fractions at a time • 2.2.3. Analysis • Analysis as total concentration in each extract

  10. EXAMPLE: Sequential Extraction Procedure for Particulate Trace Metals (Tessier et al., 1979) FRACTION 1 :Easily exchangeable fraction • For metals loosely bound to surfaces and edges of minerals, increasing the ionic strength of the solution in contact with such solids would release previously bound metals by simple exchange between cations • MgCl2 is an example salt used to increase the ionic strength of the solution • A soluble ligand (e.g. CH3COONa) is generally added to make sure that released metals remain in solution

  11. FRACTION 2 Fraction bound to carbonate minerals • Dissolution of carbonate minerals with a weak acid (e.g. CH3COOH), and as in step-1, a ligand (e.g. CH3COONa) is also added to make sure that dissolved metals remain in solution

  12. FRACTION 3 Fraction bound Fe- and Mn-oxide minerals • A reducing agent (e.g. NH2OH.HCl) is used to convert the solid and oxidized forms of Fe and Mn to reduced and soluble species (e.g. Fe2+ and Mn2+) • CH3COOH is also be added to avoid metal sorption on oxidized solid surfaces

  13. FRACTION 4 Fraction bound to organic matter • An oxidizing agent is used (H2O2) under acidic conditions (HNO3) necessary to keep metals in solution • A ligand (CH3COONH4)can also be added to avoid metal sorption on oxidized solid surfaces

  14. FRACTION 5 Refractory/Residual fraction • Requires hot digestion with strong acid mixtures (e.g. HF-HClO4)

  15. Why this order? • 1. Easily exchangeable fraction • 2. Fraction bound to carbonate minerals • 3. Fraction bound Fe- and Mn-oxide minerals • 4. Fraction bound to organic matter • 5. Refractory/Residual fraction

  16. *Environmental-Relevance*Metal bio-availability vs. fractions*Toxicity

More Related