1 / 23

Thermal Treatment/Disposal: Incineration

Thermal Treatment/Disposal: Incineration. Chapter 12. Activity. Why use incineration? What are the drawbacks?. Regulations. Historical perspective HW incinerators vs. cement kilns and light aggregate kilns and industrial boilers and furnaces. General Schematic. Rotary kiln Fixed hearth

Download Presentation

Thermal Treatment/Disposal: Incineration

An Image/Link below is provided (as is) to download presentation Download Policy: Content on the Website is provided to you AS IS for your information and personal use and may not be sold / licensed / shared on other websites without getting consent from its author. Content is provided to you AS IS for your information and personal use only. Download presentation by click this link. While downloading, if for some reason you are not able to download a presentation, the publisher may have deleted the file from their server. During download, if you can't get a presentation, the file might be deleted by the publisher.

E N D

Presentation Transcript


  1. Thermal Treatment/Disposal: Incineration Chapter 12

  2. Activity • Why use incineration? • What are the drawbacks?

  3. Regulations • Historical perspective • HW incinerators vs. cement kilns and light aggregate kilns and industrial boilers and furnaces

  4. General Schematic

  5. Rotary kiln Fixed hearth Liquid injection Cement and lime kilns Fluidized bed Boiler systems Oxygen enriched Infrared Fume Multiple chamber Multiple hearth Cyclonic Auger combustor Two-stage (starved air) Catalytic Molten salt Types of Incinerators

  6. Other Thermal Processes • Plasma arc pyrolysis • Microwave discharge • Advanced electrical reactor • In situ vitrification • Wet air oxidation • Supercritical water oxidation • Calcination • Thermal desorption

  7. Grate Open “rack” Stationary or moving Air circulation Large and irregular wastes Hearth Solid “plate” Variety of waste Suspension Sand or alumina bed fluidized with air Relatively uniform feed size Classifications of Incinerators

  8. Typical Process Flow Diagram Waste Storage Pre-processing/blending Pollution Control Incineration Flue Gas Ash Stabilization Effluent Landfill POTW

  9. Combustion Requirements 3 T’s + Excess O2

  10. Typical Excess Air Reactions CHCl+ O2 + N2 CO2 + H2O + HCl + O2 + N2 + heat

  11. Flue Gas Quench • Cool to: • 500 - 700oF for spray dryer • 180oF for low-temperature equipment • Air or water • Concurrent or counter-current flow

  12. Air Pollution Control • Pollution: • Particulates (including 10 priority metals) • Acid gases • Systems • Wet • Dry

  13. Trial Burn Test incinerator • Principal organic hazardous constituents (POHCs) destruction and removal efficiencies (DREs) • HCl • Particulates • CO • Metals • Dioxin and furans

  14. POHC DRE At least 99.99% on all selected POHCs during trial burn

  15. HCl Emissions Emission no greater than larger of 4 lb/h or 1% of HCl in stack gas

  16. Particulate Emissions At most 0.08 grains/dscf corrected to 7% O2 or 180 mg/dscm corrected to 7% O2

  17. Emissions Example Example 12-2 (p. 746) Does incinerator performance meet requirements?

  18. CO Emissions 100 ppm by volume as a 60-minute rolling average corrected to 7% O2 on a dry basis

  19. CO and Particulate Example Example 12-11 (p. 804)

  20. Combustion Efficiency At least 99.99%

  21. Dioxin and Furan Emissions 0.4 ng/dscm or 0.0001%

  22. PCBs At least 99.9999% DRE for liquid Dwell time of 2 s at 1200  100oC and 3% EA in stack gas OR Dwell time of 1.5 s at 1600  100oC and 2% EA in stack gas

  23. Design Example 12-7 (p. 765)

More Related