1 / 17

Solutions, Electrolytes, and Conductivity

Solutions, Electrolytes, and Conductivity. Lab 8. Outline. Purpose Solutions Solution Preparation from Solids Solution Preparation from Liquids (dilution) Electrolytes Conductivity Procedure Safety Concerns Waste Next Assignment. Purpose.

alice
Download Presentation

Solutions, Electrolytes, and Conductivity

An Image/Link below is provided (as is) to download presentation Download Policy: Content on the Website is provided to you AS IS for your information and personal use and may not be sold / licensed / shared on other websites without getting consent from its author. Content is provided to you AS IS for your information and personal use only. Download presentation by click this link. While downloading, if for some reason you are not able to download a presentation, the publisher may have deleted the file from their server. During download, if you can't get a presentation, the file might be deleted by the publisher.

E N D

Presentation Transcript


  1. Solutions, Electrolytes, and Conductivity Lab 8

  2. Outline Purpose Solutions Solution Preparation from Solids Solution Preparation from Liquids (dilution) Electrolytes Conductivity Procedure Safety Concerns Waste Next Assignment

  3. Purpose The goal of this experiment is to illustrate the behavior of strong, weak, and non-electrolytes in aqueous solution. This will be achieved through the use of electrical conductivity measurements. You will be afforded more experience in solution preparation.

  4. Solutions • Be able to distinguish between: • Dissolution: a solid, liquid, or gas is dissolved in a solvent • Dissociation: the breakup of compounds into simpler components, such as the dissociation of ionic compounds into ions • Types of solutions we are dealing with today: • solid to liquid • liquid to liquid

  5. Solution Preparation • When you are required to make a solution of accurate concentration, a volumetric flask is used. • We never make solutions of accurate concentration in: • Beakers • Graduated cylinders • Erlenmeyer flasks

  6. Solution Preparation from Solids • Determine the mass of the solid needed. You will need the following values first: • Molar mass of the solid • Total volume desired • Final concentration desired Calculation: • Mass, g = [ ], mol/L x MM, g/mol x Vol, L • Remember the precision of your glassware!

  7. Solution Preparation from Solids • Make the solution: • Weigh out the appropriate mass of solid. • Place a small volume of distilled water in the volumetric flask. • Add the solid to the volumetric flask. • Add some more distilled water to the flask, stopper, and invert several times. • Add distilled water to the calibration line (fill to volume) using a medicine dropper, stopper, and invert several times.

  8. Solution Preparation from Liquids • Determine the volume of stock solution needed. You will need the following values first: • Concentration of stock solution (M1) • Desired concentration of diluted solution (M2) • Desired volume of diluted solution (V2) • Calculation: • M1V1 = M2V2 • Remember the precision of your glassware!

  9. Solution Preparation from Liquids • Make the solution: • Obtain the appropriate volume of stock solution using a graduated cylinder. (Always add a few mL extra.) • Place a small volume of distilled water in a volumetric flask. • Use the appropriate pipet to transfer the correct volume of stock solution from the graduated cylinder to the volumetric flask. • Add some more distilled water to the flask, stopper, and invert several times. • Add distilled water to the calibration line (fill to volume) using a medicine dropper, stopper, and invert several times.

  10. Electrolytes Strong Electrolytes 100% dissociation and high conductivity NaCl(s) Na+(aq) + Cl-(aq) Weak Electrolytes partial dissociation and partial conductivity CH3COOH(aq) CH3COO-(aq) + H+(aq) Non Electrolytes no dissociation and no conductivity C12H22O11(s) C12H22O11(aq)

  11. Conductivity The ability of an aqueous solution to conduct electricity is dependent on the presence of ions in solution. Conductivity or K has units of S/cm, mS/cm, or S/cm. We measure conductivity so we can make a comparison regarding relative numbers of ions present in solution.

  12. Conductivity • The extent to which a solution conducts electricity is dependent on the proportional amount of ions present in solution. • Which of the following will have a higher conductivity? • NaCl vs. CaCl2 Why? • NaCl vs. C6H5COOH Why?

  13. Procedure • Soak your conductivity probe in distilled water for 30 minutes before starting your experiment. Why?

  14. Procedure Any glassware that will be containing non-electrolytes or weak electrolytes need to be rinsed thoroughly with distilled water prior to use. Make up your three known solutions. Calibrate your conductivity probe. Measure the conductivities of your known solutions, distilled water, tap water, and three unknowns.

  15. Safety Concerns • Reagents: • Acetic Acid (3%) • KCl • NaCl • Sucrose • Eye Contact: • Irritation, redness, pain, and possible damage • Skin Contact: • Irritation. May cause sensitization and / or allergic reaction. Absorption may cause symptoms similar to ingestion • Inhalation: • Irritation and coughing • Ingestion: • Gastrointestinal irritation, nausea, vomiting, diarrhea, prostration, dehydration and congestion of internal organs, and violent inflammatory reactions in the gastrointestinal tract

  16. Waste All neutral solutions can go down the drain with plenty of water when you are finished. Acidic solutions need to be disposed in the acid waste container in the fume hood. Remember to clean up the balances and counters if / when you spill anything.

  17. Lab 9 Reminder Lab 9 is next.

More Related