1 / 16

K.Somiya

Cryogenic Xylophone. GWADW @ Kyoto May. 2010 Kentaro Somiya Waseda Inst. for Adv. Study. Collaboration work with S.Hild, K.Kokeyama, H.Mueller-Ebhardt, R.Nawrodt, P.Puppo, etc. K.Somiya. Xylophone. Heat absorption via suspension fiber. ET-LF: 10K, 20kW, Silicon, DRSE + 10dB SQ

aldona
Download Presentation

K.Somiya

An Image/Link below is provided (as is) to download presentation Download Policy: Content on the Website is provided to you AS IS for your information and personal use and may not be sold / licensed / shared on other websites without getting consent from its author. Content is provided to you AS IS for your information and personal use only. Download presentation by click this link. While downloading, if for some reason you are not able to download a presentation, the publisher may have deleted the file from their server. During download, if you can't get a presentation, the file might be deleted by the publisher.

E N D

Presentation Transcript


  1. Cryogenic Xylophone GWADW @ Kyoto May. 2010 Kentaro Somiya Waseda Inst. for Adv. Study Collaboration work with S.Hild, K.Kokeyama,H.Mueller-Ebhardt,R.Nawrodt, P.Puppo, etc. K.Somiya

  2. Xylophone Heat absorption via suspension fiber ET-LF: 10K, 20kW, Silicon, DRSE + 10dB SQ ET-HF: 290K, 3MW, Silica, BRSE + 10dB SQ Single Low-T High-power IFO Problem in cooling Xylophone Cryogenic Low power + Room-T High power

  3. An issue in ET-HF heat problem • Thermal lensing • TCS noise • Parametric instability RSE Squeezing 1st generation detector: ~30kW in arm 2nd generation detector: ~800kW in arm ET-HF: 3MW in arm Can we really realize such high power?

  4. Contents of talk • Proposal of cryogenic ET-HF • Suspension-TN issue • Substrate-TE issue • Suspension-TE issue • Optimization of ET-LF

  5. Cryogenics to avoid the heat problems • Almost no thermal lensing • Room to reduce beam radius • ~0.03% deviation of T • ~50km ROC of lensing calculation by M.A.Arain • Same TN with small beam • Less overlap of opt modes • PI is eased calculation by K.Yamamoto

  6. Can we cool down the 3MW IFO? • 1ppm absorption per mirror -> 3W • f3cm Silicon fiber absorbs only 200mW Susp TN limits the sensitivity 5K Solutions • Ribbon suspension • Increase test-mass temperature ~ thin in longitudinal direction 10K ~ heat flow increases increase But thermoelastic noise becomes high.

  7. Substrate TE noise TE noise ET-HF sensitivity at 100Hz Thermal expansion is zero at T=18K,121K. Big susp TN Big TE noise Free from both problems at around 121K

  8. Thermoelastic noise of suspension Silicon ribbon w=1cm, l=60cm 5K f=2.4e-6 121K Suspension TE noise could limit the sensitivity

  9. 290K vs. 121K ET-HF sensitivity (290K) ET-HF sensitivity (121K) QN QN mirror mirror susp gravity gravity susp • l=60cm, f0.6mm silica fiber • LG33 beam • T=290K • l=60cm, 1cm x 1mm silicon ribbon (bad) • 3cm x 0.4mm ribbon (good) • TEM00 beam, w=10cm • T=121K • Mirror TN levels are almost equal • Suspension TN is low enough with the 3cm ribbon

  10. Summary of Low-T ET-HF • Thermal lensing and PI problems will be eased • With T=20K, suspension is too thick • With higher T, suspension can be thin, but TE is high • With T=121K, suspension is thin and TE is zero • Suspension TE is large, but a thin ribbon will help.

  11. Before ET-LF optimization (dashed: freq-dependent squeezing, solid: fixed squeezing) ET-LF quantum ET-HF quantum gravity gradient mirror TN susp TN opt losses are included • We could omit filter cavities to realize FD squeezing • Especially if we can make ET-LF a little wider

  12. RSE vs. Speed-meter RSE + filter cavity Resonant Sagnac (Speedmeter) • Broadband with more power • Less sensitive to mass • Less power required • Narrow-band

  13. ET-LF optimization 10kW 100kW in arm 18kW DRSE 2MW in arm 20MW in arm gravity gradient opt losses are included • The more power, the better SM sensitivity • The more power, the more thermal noise • Homodyne phase can be tuned

  14. ET-LF optimization 18kW DRSE 10kW 100kW in arm 2MW in arm 20MW in arm ET-HF (w/o filter) gravity gradient opt losses are included • Thermal noise is included • Homo-phase and mass temperature are optimized • DRSE (not yet optimized) seems better than SM?

  15. Summary and discussions • I would recommend… • 20K ET-LF + 121K ET-HF • ET-HF as an SPI for ET-LF • No filter cavity for ET-HF • Probably DRSE w/filter for ET-LF • TBD: • Payload thermal noise (Puppo. et al) • High power 1550nm LASER • DRSE optimization • Other options

More Related